Models
>
JE1340WA01
JE1340WA01 General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JE1340WA01
Viewing 1 of 1Keep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
$9.49
This part is the replacement plastic rivet, or stirrer fan cover clip for your microwave. It is made of white plastic and is approximately ¼ inch in diameter, and ½ inch long. The plastic rivet holds ...
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
$11.60
This part is the replacement light bulb for your microwave. This bulb is 125 volts and 25 watts. It should come on automatically when you open your microwave door, or if the microwave is running. If y...
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
Special Order
In Stock
Order within the next 1 hr and 19 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JE1340WA01
Viewing 4 of 4No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Andover, NJ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Microwave runs with the door open
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
and test to see if that solved the problem. If so then well done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ridgefield, CT
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would turn on and count down, but not heating and not rotate turntable. Pressing door up would occasionally start heat.
First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reco
... Read more
nnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oran from Chesapeake, VA
- Parts Used:
- WB36X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb out
The most difficult thing was removing the star security screws Both Home Depot and Lowes have tools to do this. The repair was a piece of cake, may have taken 15 min. Unplug 120v, remove case, bulb, replace and reassemble. GE doesn't want consumers fooling around inside the case, so be careful.
Was this instruction helpful to you?
Thank you for voting!