Models > DVM1950DR2WW

DVM1950DR2WW General Electric Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DVM1950DR2WW

Viewing 1 of 1

Manuals & Guides for DVM1950DR2WW

Click to download
Keep searches simple, eg. "belt" or "pump".
$18.87
This is a genuine OEM replacement grease filter for your over-the-range microwave. This part is located underneath the microwave and is designed to trap grease, preventing it from making its way into ...
In Stock
Order within the next 10 hrs and your part ships today!
This is a single OEM light bulb that brightens the surface beneath the microwave or the inside part of the microwave. This 120 volt and 20 watt light bulb gives off a soft white light, and has a clear...
No Longer Available
In Stock
Order within the next 10 hrs and your part ships today!
This secondary door switch is also known as a micro switch, and it is a genuine OEM replacement part for your microwave. The switch communicates with the electronic control board, to let it know if th...
In Stock
Order within the next 10 hrs and your part ships today!
This tray rotates in your microwave ensuring more even temperatures and is approx.14-1/2 inches in diameter.
In Stock
Order within the next 10 hrs and your part ships today!
This filter cannot be cleaned. It must be replaced.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
This part allows power to go one way only.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for DVM1950DR2WW

Viewing 6 of 6
Doesn’t shut off
Fixed by these parts
Fixing Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing Fixing Fixing
How to fix it
No heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Noisy
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Marla from Arlington, TX
  • Parts Used:
    WB24X829
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge.
306 of 361 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Theodore from Medical Lake, WA
  • Parts Used:
    WB27X10597
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Not working as far as heating or cooking
Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.
151 of 357 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Preeti from Oakland, CA
  • Parts Used:
    WB02X10956
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
replace charcoal filter
there are two screws on the top near the vent. Unscrew the two and push the vent grill/cover to the left. It slides out easily. place the charcoal filter in the exhaust slot. there is no groove/slit for it as per manual, it just sits there (almost like an afterthought in design. Prop the bottom of the filter on the stubs on the lower edge of the exhaust mouth. Slide the grill/cover back and 'click' it in. put in screws. Note, since you've opened the grill/cover you might as well wipe the grease off. I used kitchen cleaner on a paper towel.
47 of 55 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!