Models
>
PVM1790DR1WW
PVM1790DR1WW General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PVM1790DR1WW
Viewing 7 of 7Manuals & Guides for PVM1790DR1WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
This halogen light bulb is a replacement part for the bulb behind the top grill in your microwave. It is sold individually.
In Stock
$10.58
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
In Stock
On Order
In Stock
In Stock
In Stock
$40.16
The rotating ring in your microwave rests under the microwave plate, and allows it to rotate when the microwave is running. It is a round plastic ring with 3 wheels spaced out around the perimeter. If...
In Stock
$8.54
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
$13.76
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
In Stock
$15.99
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out ...
In Stock
In Stock
$29.17
This part will trip once the inside of the cavity overheats and exceeds the recommended temperature.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wesley
February 5, 2022
Turn on and runs for 3-4 seconds, then it trips the breaker in both modes convection and microwave
For model number PVM1790DR1WW
Hello Wesley, thank you for writing. The microwave is overloading the electrical circuit. In other words, the circuit is rated to handle a certain amount of amps (unit of electrical current), and the microwave is exceeding that amount, causing the breaker to trip. We hope this helps.
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for PVM1790DR1WW
Viewing 4 of 4Won’t turn on
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kim from Cliffside Park, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Naples, ME
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the vent light bulbs needed to be replaced
Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy E from Cincinnati, OH
- Parts Used:
- WB02X10750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Loss of Rack holder clip for GE Profile Convection Microwave oven
It was super easy! Opened the door, matched up the hole on the side of the microwave convection oven with the first portion of the rack holder clip, pushed in the rack holder clip and made a twist to ensure the rack holder clip seated in the wall of the oven. Less than 30 seconds to install - no tools necessary. I that the clips came
... Read more
in an order of a unit of 8 clips, allowing me a quick-fix if I need additional clips for loss. Now I have stable racks within my oven ensuring safe insertion and removal of food from the oven. Having the full use of both of the racks in my convection oven during the summer is a Godsend, especially living in the Ohio Valley with its' hot steamy summers - my kitchen stays cool as a cucumber, and so do I!
Read less
Was this instruction helpful to you?
Thank you for voting!