Models
>
JES1344SK06
JES1344SK06 General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JES1344SK06
Viewing 1 of 1
Manuals & Guides for JES1344SK06
Click to downloadKeep searches simple, eg. "belt" or "pump".
This is the replacement wave guide cover for your microwave. It is white in color and is approximately 3 ½ inches long and 4 inches wide. It has two small tabs at the top that allow it to lock into pl...
No Longer Available
This microwave turntable guide is located under the glass turntable. It is made of plastic, and comes with rollers.
No Longer Available
Special Order
Special Order
Special Order
$153.02
This part, in conjuntion with the diode and capacitor, can increase voltage from primary to very high in a short period of time and it converts that high voltage into waves of cooking energy.
Special Order
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JES1344SK06
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from KETTLE FALLS, WA
- Parts Used:
- WB24X10103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Trip breaker when opening door
Door microswith was stuck on. This is caused, I discovered, by frequently stopping the oven, while running, by opening the door rather than using the stop button. Causes the switch to arc and eventually fail. This causes the safety microswitch to trip the breaker when door is opened. There are little nubs sticking up on the spade connecto
... Read more
rs. You must squeeze them down before you can remove them from the switch. The main door switch is the upper one, mounted at an angle. You have to remove the latch assembly to remove the switch. The problem was obvious once I got the switch out. This problem could also blow the fuse, but in my case the breaker tripped first. Use an ohmmeter to check switch and fuse. The door switch is normally open. The safety switch is normally CLOSED. Instructions inside were helpful and described this problem. So, avoid this repair by always stopping oven with stop button!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from FORT COLLINS, CO
- Parts Used:
- WB48X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wave guide cover one of the pins holding it in place was missing / cover loose
I simply removed the other push pin holding in the old cover and put the bottom in first and snaped into place at the top. The whol job took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from POTOMAC, MD
- Parts Used:
- WB27X10567
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Power cut off to Microwave - It was run empty
1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the ma ... Read more in panel.
5. Reinstall microwave and trim kit
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the ma ... Read more in panel.
5. Reinstall microwave and trim kit
Read less
Was this instruction helpful to you?
Thank you for voting!