JEM6F01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Luis from Plano, TX
- Parts Used:
- WB27X1160
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Noise and no Heat on Microwave oven.
First, I waste $65 by calling some "REPAIR" service. They showed at home and charge me that just to tell me
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!
Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!
Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from NEWTON, NJ
- Parts Used:
- WB27X7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
PS240270 Ceramic Fuse - 15 Amp
PS240270
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SAN JOSE, CA
- Parts Used:
- WB27X7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
CERAMIC FUSE BLEW WHILE HEATING VEGETABLES
I found an exploded view diagram of of my microwave model which was very helpful. You need only remove outside metal skin by removing 4 screws on either side and 4 more on the back. Remove 4 plastic hole plugs from the top mounting inserts. Gently pull sides out and lift up and back to remove outer skin. The fuse is located on the back right corner behind the control panel. You access from the side. The fuse is under the spreader bar. Lift fuse up gently to remove.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Pittsford, NY
- Parts Used:
- WB2X7640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken plastic rack support
attached new support in about 5 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Palm Desert, CA
- Parts Used:
- WB2X7640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken rack support.
Removed the broken support by twisting counterclockwise, and inserting the new one and twisting it to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Las Vegas, NV
- Parts Used:
- WB2X7640
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
We had hglued the bad support that is why it took time to remove the dried glue first.
After removing the glue we were able to twist the part in. We did not want to break the flange on then part so took our time and did it gently.
Was this instruction helpful to you?
Thank you for voting!