Models > JNM3184RP9SS

JNM3184RP9SS General Electric Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JNM3184RP9SS

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
The stirrer fan cover in your microwave can be found on the roof of the microwave. It protects the fan from damage and debris. This fan cover is made of white plastic and is approximately 7.5 inches i...
In Stock
Order now and your part arrives by Mar 19
$28.79
Sold individually. Appliance may take 2.
In Stock
Order now and your part arrives by Mar 19
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
Order now and your part arrives by Mar 19
In Stock
Order now and your part arrives by Mar 19
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
In Stock
Order now and your part arrives by Mar 19
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
In Stock
Order now and your part arrives by Mar 19
This switch monitor interlock helps your microwave detect when the door is properly closed. If it’s damaged, the microwave may not start. Replacing it restores safe operation and is a quick fix with basic tools.
In Stock
Order now and your part arrives by Mar 19
Keep your microwave working safely and efficiently with this aluminum mesh grease filter. Sized at 7.5 by 5 inches, it fits into the underside of your microwave, right above the cooktop, and helps tra...
In Stock
Order now and your part arrives by Mar 19
The Vent grille covers components inside the microwave while allowing airflow through the slats.
In Stock
Order now and your part arrives by Mar 19
$20.95
This microwave vent damper assembly helps control airflow by directing exhaust out of the kitchen and preventing outside air, smoke, or odors from flowing back in when the fan is off. Made from durabl...
In Stock
Order now and your part arrives by Mar 19
$23.05
This fan blade, also known as a stirrer blade, is a genuine OEM replacement part for your microwave. This is a fairly easy repair. To complete it, you will need a screwdriver to disassemble the fan as...
In Stock
Order now and your part arrives by Mar 19
$19.90
In Stock
Order now and your part arrives by Mar 19

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for JNM3184RP9SS

Viewing 5 of 5
No heat
Fixed by these parts
Fixing Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing
How to fix it
Doesn’t shut off
Fixed by these parts
Fixing
How to fix it
Door not closing properly
Fixed by these parts
Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gregg from Santa Ana, CA
Parts Used:
WB27X35382
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave made loud buzz noise and did not heat
I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple sett ings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one
42 of 81 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from UTICA, NY
Parts Used:
WB06X10712, WB01X45506
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
cover stirrer fan was burned and sparking in three part even the plastic rivet
just in 1 2 3 step easy way. First unplug the power cord,use a small flat-head screwdriver to pull out the plastic rivet pin,rotate the old cover counter clockwise to removed lift out the blade assembly, install the new cover stirrer fan by first positioning the blade assembly then align the cover and rotate it clockwise to secure, then r eplace the mounting plastic rivet pin;with the repair completed, plug the power cord back in and your microwave oven should be ready for use again. : )
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Seven from MOUNT AIRY, MD
Parts Used:
WB27X35382
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave not heating.
Followed the instructions on your website and a YouTube video. The diode was at a 90 degree angle which made it a little trickier. Unfortunately the repair did not resolve the problem. I ended up buying a new microwave for temporary use for less than ordering any more parts. We are pleased with your website, instructions, ease of inst allation though!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!