Models
>
JVM1631BH002
JVM1631BH002 General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JVM1631BH002
Viewing 7 of 7Keep searches simple, eg. "belt" or "pump".
$10.58
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
In Stock
In Stock
In Stock
In Stock
$8.54
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
This is not the entire door, just the framing around the front of it.
No Longer Available
In Stock
$15.99
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out ...
In Stock
In Stock
In Stock
$199.77
Genuine OEM magnetron for your microwave. Always use proper safety equipment and follow the manufacturers instructions while installing.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JVM1631BH002
Viewing 5 of 5No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kim from Cliffside Park, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Fort Worth, TX
- Parts Used:
- WB55X10813
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Outer frame had a crack and needed to be replaced
Had to discover how to do this the hard way, but the 1st thing you need is a blow-up diagram of the door which you can download from GE's website.
Note that all the components in the door save for the 2 handle screws are snap-on.
You will need a screwdriver and a putty knife.
The door assembly is on a simp ... Read more le pivot hinge which you can lift and pull off the microwave, making it easier to work.
On the inside face of the door, locate strip where the outer edge meets the inner door. The plastic strip is about 2" wide and goes all the way around the door. Remove this strip using a putty knife working around it to gently pry it off. Push putty knife into space between plastic strip and outer door panel. This will give access to the 2 handle screws.
Unscrew the screws and remove handle.
Using putty knife and starting at the top edge of the door near the center, gently pry the outer frame from the latching tabs until the frame comes off.
Snap on new frame and working backwards, screw back the handle, then snap back the the plastic strip and rehang your door on the pivot hinge.
Remember the parts are plastic so don't over tighten the screws.
Also remember to clean the outer glass panel inside and outside before snapping on the outer frame or your fingerprints will be on your microwave.
Note that all the components in the door save for the 2 handle screws are snap-on.
You will need a screwdriver and a putty knife.
The door assembly is on a simp ... Read more le pivot hinge which you can lift and pull off the microwave, making it easier to work.
On the inside face of the door, locate strip where the outer edge meets the inner door. The plastic strip is about 2" wide and goes all the way around the door. Remove this strip using a putty knife working around it to gently pry it off. Push putty knife into space between plastic strip and outer door panel. This will give access to the 2 handle screws.
Unscrew the screws and remove handle.
Using putty knife and starting at the top edge of the door near the center, gently pry the outer frame from the latching tabs until the frame comes off.
Snap on new frame and working backwards, screw back the handle, then snap back the the plastic strip and rehang your door on the pivot hinge.
Remember the parts are plastic so don't over tighten the screws.
Also remember to clean the outer glass panel inside and outside before snapping on the outer frame or your fingerprints will be on your microwave.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Coulterville, CA
- Parts Used:
- WB21X10148, WB26X32629
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No power to microwave, no heating.
Unpluged power cord!! Removed front control panel to expose electronics (need to remove top horizontal vent cover to expose mounting hardware). Unplugged leads to control panel board. Removed magnetron with Tstat (3- phillip heads, need stubby). Installed new parts and control panel, plugged it in tested. Done.
Was this instruction helpful to you?
Thank you for voting!