Models > CVM521P2M5S1

CVM521P2M5S1 General Electric Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CVM521P2M5S1

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
Lamp also known as light bulb. Sold individually.
In Stock
Order now and your part arrives by Mar 19
This interlock switch is located in the door latch.
In Stock
Order now and your part arrives by Mar 19
It is recommended to replace this filter yearly.
In Stock
Order now and your part arrives by Mar 19
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
Order now and your part arrives by Mar 19
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
In Stock
Order now and your part arrives by Mar 19
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
In Stock
Order now and your part arrives by Mar 19
This switch monitor interlock helps your microwave detect when the door is properly closed. If it’s damaged, the microwave may not start. Replacing it restores safe operation and is a quick fix with basic tools.
In Stock
Order now and your part arrives by Mar 19
Keep your microwave working safely and efficiently with this aluminum mesh grease filter. Sized at 7.5 by 5 inches, it fits into the underside of your microwave, right above the cooktop, and helps tra...
In Stock
Order now and your part arrives by Mar 19
$20.95
This microwave vent damper assembly helps control airflow by directing exhaust out of the kitchen and preventing outside air, smoke, or odors from flowing back in when the fan is off. Made from durabl...
In Stock
Order now and your part arrives by Mar 19
$52.99
In Stock
Order now and your part arrives by Mar 19
No Longer Available
In Stock
Order now and your part arrives by Mar 19

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for CVM521P2M5S1

Viewing 6 of 6
No heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Doesn’t shut off
Fixed by these parts
Fixing Fixing
How to fix it
Door not closing properly
Fixed by these parts
Fixing Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from Andover, NJ
Parts Used:
WB24X10047
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Microwave runs with the door open
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
37 of 58 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Ridgefield, CT
Parts Used:
WB24X10047
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave would turn on and count down, but not heating and not rotate turntable. Pressing door up would occasionally start heat.
First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reco nnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.
40 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregg from Santa Ana, CA
Parts Used:
WB27X35382
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave made loud buzz noise and did not heat
I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple sett ings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one
42 of 81 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!