Models
>
PEM31BM1TS
PEM31BM1TS General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PEM31BM1TS
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
The door interlock switch bracket houses and supports the door switches.
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
On Order
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for PEM31BM1TS
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from NORWALK, CT
- Parts Used:
- WB10X27080, WB14X10049
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door was hard to open
1. Take out the case by unscrew 8 screws on the back and side of the case
2. Take out the control panel by unscrew 1 screw on the top and slide up
3. Take out the latch by unscrew 2 screws, and slide out 3 electric switches that clipped on the latch
4. Clip the switches onto the new latch
5. Slide in lever switch into ... Read more latch
6. Put back the latch
7. Put back the control panel
8. Put back the case
2. Take out the control panel by unscrew 1 screw on the top and slide up
3. Take out the latch by unscrew 2 screws, and slide out 3 electric switches that clipped on the latch
4. Clip the switches onto the new latch
5. Slide in lever switch into ... Read more latch
6. Put back the latch
7. Put back the control panel
8. Put back the case
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from WESLEY CHAPEL, FL
- Parts Used:
- WB14X10049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door locks. Not opening.
Slide a Butter knife at left side by open push knob door will open. Then open all screws from top cover push cover top side front way then door locks Bracket have 3 microswitch pulls out switches mark them top medium and bottom. Remove 3 screws holding brackets will come out. On bottom see a Cam has 1/4” holes can holding Saft broken then
... Read more
install new door lock bracket install microswitch put 3screw and slide Cam on saft . I put a small screw on saft to hold cam on place. There was no screw . That’s why cam saft was broke. Put top cover tight all the screws and door lock fixed.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James A from SILVERDALE, WA
- Parts Used:
- WB26X10252
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the cover for the tray motor was attached to the bottom cover at 6 points. they were 3mm to 4mm long.
I used small wire cutter I use in fly tying hobby. The metal was easy to cut. When cover was removed I unplugged the motor,removed it and plugged the new one in.
To replace the cover -- reverse it,place the 2 tabs on one edge into the slots that are already part of the base. On the opposite edge there is a domed shaped tab with a h ... Read more ole in center. Place the small screw that was provided back in and thighten.
Your Done
To replace the cover -- reverse it,place the 2 tabs on one edge into the slots that are already part of the base. On the opposite edge there is a domed shaped tab with a h ... Read more ole in center. Place the small screw that was provided back in and thighten.
Your Done
Read less
Was this instruction helpful to you?
Thank you for voting!