Models
>
FMT148G1W2
FMT148G1W2 Frigidaire Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FMT148G1W2
Viewing 8 of 8
Manuals & Guides for FMT148G1W2
Click to downloadKeep searches simple, eg. "belt" or "pump".
This vent hood filter collects grease particles in the air from cooking. Sold individually.
No Longer Available
$92.58
This charcoal air filter is eleven inches long, and six inches wide. It is used for some Frigidaire/WCI brand microwave ovens.
Special Order
Special Order
This is the glass that covers the bulb on the undercarriage of the microwave.
No Longer Available
Special Order
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FMT148G1W2
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stuart from North Port, NY
- Parts Used:
- WB2X9883
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace Charcoal Filter
Philips head screwdriver to remove 2 screws holding plastic grill above microwave door in place. Old Filter lifts out slide new filter in. It rests on an angle. Re insert Grill (careful that plastic tabs slide into proper slots). Tighten SCrews
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Freddie from Roanoke, VA
- Parts Used:
- 5304409136
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door window seal damaged.
The "seal" is a clear plastic sheet that forms the inner most layer of the "window" in the microwave door. If it becomes damaged or doesn't adhere properly, steam and other cooking by-products get inside the door itself. That's what happened in my case. As a result, I had to disassemble the entire door to clean the inside of the glass
... Read more
and other parts. If that cleaning had not been necessary, I could have replaced the seal without disassemblying the door.
To replace the seal, I followed these steps:
1. Used my thumb nail to raise a corner of the old seal.
2. Peeled off the old seal. This leaves a perforated metal layer exposed.
3. Cleaned the metal layer to remove residual adhesive from the old seal.
4. Once the metal layer was dry, my wife and I worked together to peel off the "backing sheet" from the new seal. (One side of the seal has adhesive on it - like the sticky side of tape. After you peal the backing off, the sticky side is exposed.)
5. After we CAREFULLY aligned the seal, I held it while my wife slowly and carefully pressed it into place.
Problems to watch out for:
The seal is shipped "folded". This causes a crease to form in the plastic seal, which makes it difficult, if not impossible to install it without leaving any raised places. Note that raised areas in the center probably just look bad. But, raised areas around the edge may prevent a proper "seal" and result in steam, etc., getting inside the microwave door. I receved two separate seals and both had a crease. PartSelect reps were very nice, but were not able to correct the problem.
To replace the seal, I followed these steps:
1. Used my thumb nail to raise a corner of the old seal.
2. Peeled off the old seal. This leaves a perforated metal layer exposed.
3. Cleaned the metal layer to remove residual adhesive from the old seal.
4. Once the metal layer was dry, my wife and I worked together to peel off the "backing sheet" from the new seal. (One side of the seal has adhesive on it - like the sticky side of tape. After you peal the backing off, the sticky side is exposed.)
5. After we CAREFULLY aligned the seal, I held it while my wife slowly and carefully pressed it into place.
Problems to watch out for:
The seal is shipped "folded". This causes a crease to form in the plastic seal, which makes it difficult, if not impossible to install it without leaving any raised places. Note that raised areas in the center probably just look bad. But, raised areas around the edge may prevent a proper "seal" and result in steam, etc., getting inside the microwave door. I receved two separate seals and both had a crease. PartSelect reps were very nice, but were not able to correct the problem.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from McDonough, GA
- Parts Used:
- 5304408949
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace the bulb
Unscrew the glass lamp cover and replace the bulb. Very simple. The hardest part was to find the bulb. I looked at my local hardware stores but of course they did not have them. This site was great and easy to order. I looked at 3 other sites before finding this one to be the most simplistic to use.
Was this instruction helpful to you?
Thank you for voting!