LMV1635SB ((ABKELGA)) LG Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from BILLINGS, MT
- Parts Used:
- 3B73362F
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken door micro switch. (unit does not start heating)
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far left side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from kewanna, IN
- Parts Used:
- 5230W1A012E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed grease filters for a used over range microwave
ordered on the part select web site, came quickly, order was correct
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from DETROIT LAKES, MN
- Parts Used:
- 1B71961H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the round glass tray
new glass tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from ARCADIA, CA
- Parts Used:
- 3B73362F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Door sensor switch went bad. Microwave would not operate.
Watched a couple of repair videos on Youtube by searching for the model number. Found out what to do in order not to get shocked by the powerful capacitor.
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the directions to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the directions to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from BRONX, NY
- Parts Used:
- 5889W2A012F, 1B71961H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass was cracked and the turntable burned
Just removed and replaced by putting the new turntable and glass in, 1, 2, 3; that's it. I'm so thankful for this site because I would have had to buy a whole new microwave. Thanks a million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from LANCASTER, CA
- Parts Used:
- 3552W1A032J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The major plastic frame was broken at the screw hole support. I was sent the wrong part and found out the part I needed was no longer made and would have to buy a new door for $150.
The wrong part was under $20. When I found out I had to replace the whole door for $150. I decided DYI was the way to go. I used JB weld and the door looks and works like a charm. Give plenty of time to cure all water needs to be cured out if exposed to microwaves. No problems so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from LUXEMBURG, WI
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The over the stove microwave door would not close.
I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from DEPEW, NY
- Parts Used:
- 3B73362F
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not start when closing door.
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from HUFFMAN, TX
- Parts Used:
- 0CZZW1H004S, 3B74133Q
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
MICROWAVE OVEN JUST SHUT DOWN, NO POWER,
TOOK OUT ALL SCREWS FRONT OVER DOOR AND AROUND FRONT FRAME, LIFTED FRONT FACE OFF, FIRST CKD FUSE, BUT FUSE HAS A WHITE GLASS SO DIDNT KNOW IF IT WAS GOOD OR BAD, NEXT THING I SAW WAS THE HIGH VOLTAGE CAPACITOR, BUT CKD YOUR PRICES ON THE PARTS AND THEY WERE TWO OF THE CHEAPEST TO REPLACE, IT WAS REALLY GUESS WORK ON MY PART, SEE I USED TO WORK ON OVERHEARD CRANES IN A FACTORY, I LEARNED WHEN THEY OUIT WORKING IT WAS USALLY EITHER A FUSE OR A CAPACITOR, SO MY GUESS WORK WAS IN MY FAVOR, AND MY MICROWAVE CAME TO LIFE, I THANK YOU FOR THE NICE EMPLOYEES YOU HAVE WORKING AT PART SELECT FOR THEIR HELP AND GREAT SERVICE, DARRELL INGLE , HOUSTON TEXAS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from DELAND, FL
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door would not shut completely and would not activate switches
After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CLERMONT, FL
- Parts Used:
- 6600W1K001R, 3B73362F
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave Timer would count down, but unit would not heat. Turntable not turning.
Replaced entire door latch assembly with the three micro switches. Easier to replace entire latch assembly as individual switches do not remove easily from latch assembly. Had trouble removing front panel assembly. Parts ordered solved this problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from FOREST, VA
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door locker snapped off
Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from MORENO VALLEY, CA
- Parts Used:
- 4900W1A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wanted to see the instructions before I install it.
Wanted to see the instructions before I install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from TAMARAC, FL
- Parts Used:
- 3550W1A126D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
did not include screw to secure it to celing of the microwave rempved
removed old cover put the new one in place found right size screw from my tool box, tightened it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HENDERSON, NV
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave dish would not move back and forth
unscrewed the bottom of the microwave and unplugged old part then took the screw out and put new one in. Super easy!
Was this instruction helpful to you?
Thank you for voting!