KEMS376TBL2 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Bainbridge Island, WA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert S. from Stafford, TX
- Parts Used:
- 4392027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Close the door on the microwave, punch in the # nothing happened
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.
The parts was delivered almost before my notice they were shipped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from STOW, OH
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burnt out bulb
took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks
lost the owners manual,
part select's schematics were very helpful
thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Chester, CA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Fan motor and magnetron did not come on, but every thing else did.
Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Patrick from Baltimore, MD
- Parts Used:
- 4392027
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Needed to push door up to run appliance.
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Santa Maria, CA
- Parts Used:
- WP3177420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
used up elec baking element
Unscrew the old one, pull it out, along with a few inches of wire. Use a couple of clothes pins to keep the wire escaping back behind the oven as you unhook them from the damaged (bad) one. Then reverse the process with the new one. No big deal. Works great now and the wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KELVIN from SOUTHFIELD, MI
- Parts Used:
- WPA3073101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light blew out
change light bulbs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Skokie, IL
- Parts Used:
- WP4168403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic oven knob broke.
I took the new knob out of the plastic bag and placed it on the oven. The whole process took les than one minute and no tools were needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Auburn, AL
- Parts Used:
- 3185368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven was missing one of its racks
Just slid new rack in. Looks great! Thanks for having just what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Punta Gorda, FL
- Parts Used:
- WP3177420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burnt out baking element
After 26 years, the element burned out. I followed the diagrams on this website. Basically, I took out the screws that hold the element in place and carefully pulled the old element forward. The wires had fittings that slipped off the old element (with a little help from the wrench.) When the wires were disconnected, I clipped the adjustable wrench on the one of them to make sure they didn't slip back through the holes in the back of the oven. The old fittings slipped right onto the new element (couple of taps with a small hammer to get them all the way on). Them I slipped the wires back through the holes and put the two small screws in the plate at the back of the element. Quite simple, even for a guy with four thumbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Collins, CO
- Parts Used:
- WP8189867
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
light wont come on
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from PENFIELD, NY
- Parts Used:
- WP3177420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element broke after 35 years of use.
Turned off breaker, verified that the breaker controlled the oven and was actually off.
This is important since you can still get a shock from leaks in the neutral side that may surprize you if you ground one side. Also some breakers can be mislabeled on older homes.
I removed the two screws holding the element to the back of the oven phillips #1 screw driver.
I carefully guided the wires and attached terminals out of the recess until
I had about 5 Inches of wire inside the oven exposed. Just be patient and careful, they will come out.
I then unpluged the wires from the old element and attached a binder clip to the ends so they could not slip back into the oven shell. Clothes pins are also a good choice or some duct tape.
I thoroughly cleaned the oven.
I then installed the wire terminals to the new element and reversed the removal procedure.
I then verified function and temperature of the oven settings.
It took me 10 minutes not including oven cleaning time.
This is important since you can still get a shock from leaks in the neutral side that may surprize you if you ground one side. Also some breakers can be mislabeled on older homes.
I removed the two screws holding the element to the back of the oven phillips #1 screw driver.
I carefully guided the wires and attached terminals out of the recess until
I had about 5 Inches of wire inside the oven exposed. Just be patient and careful, they will come out.
I then unpluged the wires from the old element and attached a binder clip to the ends so they could not slip back into the oven shell. Clothes pins are also a good choice or some duct tape.
I thoroughly cleaned the oven.
I then installed the wire terminals to the new element and reversed the removal procedure.
I then verified function and temperature of the oven settings.
It took me 10 minutes not including oven cleaning time.
Was this instruction helpful to you?
Thank you for voting!