KBMC147HBL2 KitchenAid Microwave Oven Combo - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

After popping the last few kernals of popcorn, we hear a different kind of pop sound come from our microwave oven. When we looking inside, we found that the glass turntable had broken unevenly in half. Although we didn't understand why it had happned, we did know we'd be without the use of the microwave without a new one. After less than 10 minutes surfing online, I had found the correct part on PartSelect.com and had arranged to have it shipped to me by speedy delivery. Once it arrived, I just popped the new turntable into the microwave and used the box to dispose of the broken one. It could not have been easier and it saved me the cost of a service call and likely further delay.

Remove 4 screws holding plastic vent between microwave and oven. Take off plastic vent. Remove two metal clamps at bottom of stainless panel (one screw on each clamp). Open door, remove two screws (recessed) at top of door that hold stainless panel (careful as panel is only connected by these screws and is heavy and door will spring shut without the weight of the panel...even with only one good spring) and put stainless door panel aside.

From bottom of door, remove two screws holding black plastic panel and put plastic panel aside. You should see the broken spring- remove it and replace with new spring. Note - hook the "lower" half of spring (the end with the U hook) first, then wedge/slide the other end until it hooks into slot.

Put parts back together in reverse order.

1)Power off 2) Remove frame covering front timer display - screw on the bottom 3) unscrew time display - 4 screws 4) unsnap lamp spring clip 5)replace lamp

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This one is painted model and the door has 2 screws at the bottom and 2 at the top to take out to get the front of the door off. First remove the vent assembly at the bottom of the door by removing the 4 screws.Hold the door together(I finally used a big piece of masking tape to hold the door top together to get it back together). Take the bottom screws out first and then holding the door front from underneath open the door to get at the top 2 inside screw. and pull it away carefully from the inner door parts and lay it aside on a carpet of towel.Then the fun begins-takingout 2 screws holding the plastic inner door cover to get at the torsion springs at the bottom of the door. these screw ar near each end of the plastic part but the left one is directly above a vent sticking out fromthe back of the oven below. There is only about #/4- i inch space to get a screw driver onto the phillips head screw. I have alot of small screw driers butnot even aphillips head fro a drill driver is short enough to get into the space. I used apreviously bent small screwdiriver to get the screw out. I tried to bend another screwdrover to a shorter dostance but it snapped off in the bending process. I fanally got it out and replaced the broken spring. Tbouth a set of sprnings that were supposed to be the same for left and right sides so I decided to replace oth springs while I had it apart. The right side spring went in fairly easily after figuring out how th thread it into the holes. The unbroken spring wass not so easy. I finally idcovered that the new spring ws not bent the same as the original one and was not going to go in the place of the old one. I ended up putting the old one back in and putting the dooor together with a little difficulty. I replaced the bottom screw on the door with longer ones as well as the upper ones and got a much better job done.

I took out the old chipped dish and replaced with the new dish...

The instructions from another customer was helpful. I concur with another comment I read while researching this proceedure. What Idio-- would design a microwave that required pulling the unit from the wall and removing the top panel just to access. It is good idea to unplug the transformer and capacitor wires before proceeding. I also googled a schematic to see the parts layout. Remember not to touch the bulb with your fingers. Use a cloth or paper towel.

I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.

When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.

All seems to be working well now.

Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?

I just placed the tray in and was done. The kicker is that i cannot use my microwave without the tray. so i was without my microwave for 2 weeks before i called parts select. they were quick and fast.

easily IDed parts; ordered, here 3 days later. very convenient. no hassle. no wasted time going from place to place or calling everyone in yellow pages.

This is the third time that the bulb went out.It took two Sears service technitions to remove the entire appliance out of the cabinet. The entire top has to be removed and the insolation has to be pulled back to get to the electrical wire. I am waiting for an appointment to get Sears to do it again. The door springs have broken and you have to make sure the door is closed before walking away. It has a heavy glass and the weight is pretty heavy. Robert.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner

Ordered a new one, put it in place in less than one minute.