Models > JMW8530CAS

JMW8530CAS Jenn-Air Microwave Oven Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JMW8530CAS

Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and uns...
In Stock
This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temp...
In Stock
$13.24
Sold individually.
In Stock
If your oven door is not opening or closing easily, there may be an issue with the door hinge. The hinge uses spring tension to allow the door to stay open at an angle instead of dropping open. This g...
In Stock
$20.77
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
This electronic clock assembly is seven and a half inches long. It is three inches wide and is intended for use with a range's control panel.
In Stock
$85.14
The oven rack provides a stable surface for cookware inside the oven. Sold individually.
In Stock
$127.00
This bake element is found on the bottom of the oven.
In Stock
This part goes over top of the light bulb.
In Stock
$8.04
In Stock
$102.61
This oven door gasket prevents heat from escaping the oven cavity when in use.
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for JMW8530CAS

Viewing 10 of 10
Little to no heat when baking
Fixed by these parts
Fixing Fixing
How to fix it
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Will not program
Fixed by these parts
Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Little to no heat when broiling
Fixed by these parts
Fixing Fixing
How to fix it
Door won’t open after self cleaning cycle
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Westford, MA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
157 of 200 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
charles from marstons mills, MA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa ilure to do so will cause the plastic plug connector to melt from oven heat.
75 of 101 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Statesville, NC
Parts Used:
WP74008014
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven door wouldn't close completely
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs a ren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.
61 of 68 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!