Models
>
GC932EXD8
GC932EXD8 Frigidaire Microwave Oven Combo
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GC932EXD8
Viewing 11 of 11Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
$74.13
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner
Special Order
$106.22
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
In Stock
In Stock
In Stock
This safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.
No Longer Available
$9.48
This is an authentic mounting screw, which works with ranges, wall ovens, cooktops and warming drawers.
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GC932EXD8
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jonathan from Arkport, NY
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module
... Read more
not working if oven is on, but I think it is because there is no air circulation behind the stove.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Middle Village, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two top burners would not light, defective switch
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a m
... Read more
inute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from El Paso, TX
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Was this instruction helpful to you?
Thank you for voting!