GC932EXH5 Frigidaire Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jonathan from Arkport, NY
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Middle Village, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two top burners would not light, defective switch
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from El Paso, TX
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Okeene, OK
- Parts Used:
- 5303131115
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original drip pans were rusting on the undersides
Just to point out the pans were delivered within a few days which was very quick. I just dropped them in. They fit perfect. Thank You for no stress.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter G from Pine River, MN
- Parts Used:
- 5303912679
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven igniter glows but does not light.
I first unplugged the power cord and raised the range top and shut off gas supply to oven. then i removed the broiler drawer. Then using the adjustable wrench i loosened and removed the gas supply line from safety valve. Then using the philips head screw driver i removed the 2 screws holding the heat sheild surounding the valve. Then i unplugged the 2 wires on the valve body. then i removed the 3 screws from valve bracket and removed the valve. Install in reverse order and adjust gas orfice for proper burner flame using adjustable wrench. takes about 30 mins. I have done this repair once befor so i kinda knew what i was doing from the get go!!!! I had the new part i had ordered from this site in just 3 days!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mavis from McKees Rocks, PA
- Parts Used:
- 5303131115
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replace Chrome Drip Pan
No installation steps required. I did have very fast delivery of parts ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Len from Corry, PA
- Parts Used:
- 316035200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Switch plate cracked.
This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from rosemount, MN
- Parts Used:
- 5303912679
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Oven burner would not ignite
I determined the safety valve must be defective. The model number of the Okeefe-Merrit/Tappan/Frigidaire/Electrolux stove (27 yrs old) could not be found online nor at Frigidaire's parts call center. However, due to Partselect's most helpful picture parts pages, I was able to find my valve with the part number clearly showing for me to see. No picture, no resolution. The info sheet with the part was beneficial and placement time was 15 minutes.
I raised the cook top and removed the fuse in the back, right corner and shut off gas at front left corner. After using meter to be sure there was no power, I marked the wires as front and back, disconnected them using needle nose, disconnected gas line using two wrenches, removed three screws in retaining bracket before sliding unit out. Installation was the reverse.
With fuse replaced before installation I measured 120 volts across the two wires. (Don't try to do it hot.) When attached to the valve the measure went down to 2.9 volts. After installation and all restored, it took about 1 to 1 1/2 minutes for ignition.
I may have saved myself the purchase of a new stove just now, but after 27 years I think she is going to want a new kitchen. It was worth the repair and Partselect was prompt with the delivery. Happiness returns to a disgruntled cook.
I raised the cook top and removed the fuse in the back, right corner and shut off gas at front left corner. After using meter to be sure there was no power, I marked the wires as front and back, disconnected them using needle nose, disconnected gas line using two wrenches, removed three screws in retaining bracket before sliding unit out. Installation was the reverse.
With fuse replaced before installation I measured 120 volts across the two wires. (Don't try to do it hot.) When attached to the valve the measure went down to 2.9 volts. After installation and all restored, it took about 1 to 1 1/2 minutes for ignition.
I may have saved myself the purchase of a new stove just now, but after 27 years I think she is going to want a new kitchen. It was worth the repair and Partselect was prompt with the delivery. Happiness returns to a disgruntled cook.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from GLEN MILLS, PA
- Parts Used:
- 5303204154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rusted out front burner
remove screw, remove burner, install new burner and screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from REDFORD, MI
- Parts Used:
- 5303131115
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace Drip Pans
No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SPENCERPORT, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad igniter in switch
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
Was this instruction helpful to you?
Thank you for voting!