Models
>
RKT-396
RKT-396 Caloric Microwave Oven Combo
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for RKT-396
Viewing 13 of 13
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Aug 16
$54.95
This is an authentic OEM replacement part. This wire oven rack is used un ranges, microwave oven combs, and wall ovens. This wire rack is made of metal, and it is chrome in color. It is approximately ...
In Stock
Order now and your part arrives by Aug 16
$5.12
This is a ceramic fuse for a microwave. It is just over 1 inch long. This fuse is 20 amps and 250 volts. This part powers your microwave. If your appliance is not heating properly, or is not turning o...
In Stock
Order now and your part arrives by Aug 16
In Stock
Order now and your part arrives by Aug 16
$82.76
This is an authentic OEM replacement part. This oven light assembly is used in a number of appliances, most often it can be found in ranges, wall ovens, microwaves, and microwave oven combos. This lig...
On Order
This OEM replacement part has been sourced from the manufacturer.?This hinge kit is designed for use with ranges and wall ovens. The hinges allow you to easily open and close the door on your applianc...
No Longer Available
This gas burner grate is used for some gas ranges and cooktops. This is a black burner grate with each side measuring almost eight inches.
No Longer Available
This is an authentic OEM replacement part. This hinge kit is commonly used with ranges. Working hinges allow you to easily open and close the door on your range. This kit comes with the hinge and the ...
No Longer Available
Special Order
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
This burner ignition switch is a little over an inch long. It is made of plastic and has a white center cam. This switch has some metallic components.
No Longer Available
Common Problems and Symptoms for RKT-396
Viewing 5 of 5Won’t turn on
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jay from Edwardsville, IL
- Parts Used:
- WPM0805101, D8547912
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Blows main fuse when the microwave generator start, (cooking function).
Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter.
Tried fuse, it does not blow untill cooking starts.
Check capacitor with ohm meter, after properly performing capacitor dischagre procedure.
Order new capacitor, simple installation. another new fuse and all is good and cooking again.
Tried fuse, it does not blow untill cooking starts.
Check capacitor with ohm meter, after properly performing capacitor dischagre procedure.
Order new capacitor, simple installation. another new fuse and all is good and cooking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tad from tamarack, MN
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read more
e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Martinsville, IN
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this instruction helpful to you?
Thank you for voting!