RKS394 Caloric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Marietta, GA
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulb burned out
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from GLOVERSVILLE, NY
- Parts Used:
- Y07491300
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Oven Would Not Light
Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth Coates from Washington, DC
- Parts Used:
- WP314647B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
loss burner grate
Just set in the new grate and start cooking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perth Amboy, NJ
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from La Junta, CO
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Panel light burnt out after 10 years
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Las Cruces, NM
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lake George, CO
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from WESTFORD, MA
- Parts Used:
- Y07623602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top oven gasket replaced
shortened gasket for this oven. moved hook approx. 1 inch. used high temp adhesive. simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuong from plano, TX
- Parts Used:
- D8547912
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Fuse blows when start cooking.
Replace the capacitor and the fuse. Then it works again. Part arrived in an open plastic bag with scratch. It looked like a returned part, but it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine M. from Fork Union, VA
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
my stovetop light did not work
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Biao from Houston, TX
- Parts Used:
- D8547912
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Maytag Microwave UMC5100AD fixes
My Maytag Microwave UMC5100AD was suddenly broken in 1 second when I heated food last time. Then no clock, etc, seem the fuse broken. to fix it, the most difficult part was how to remove it from the wall trim. Finally got it out. Then went HomeDepot to get the same fuse, replaced and used it, burned again. Then I searched online and ppl said the capacitor might be the one. I took it out and measured it, yeah it indeed was a problem since it's not open. Then I order the capacitor from PartSelect about $32. After 3 days I got it and installed it. Done. Sure need to put the Microwave back to wall trim. That's it. Saved about $500 buck if I buy a new one plus labor to install it. Thanks
Was this instruction helpful to you?
Thank you for voting!