The drive hub connects the basket of your washer to the transmission shaft, which in turn allows the basket to spin. If your washer will not agitate, spins slowly, or is excessively noisy, it may requ...
The washer drive pulley kit is also known as a replacement clutch assembly, or a cam kit. The drive pulley is found at the bottom of your washing machine, mounted to the drive shaft. Common symptoms i...
The drive belt works with the pulley in your washer in order to spin the tub. If you notice a burning rubber smell, your washer has become excessively noisy, or it will not spin, it could indicate an ...
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
This is a genuine OEM door lock assembly for a top load washing machine. This part is also known as a door switch, and it is used to communicate whether the door to the washer is opened or closed. If ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
If your washer is leaking, will not fill with water, or will not stop filling, there may be an issue with your water inlet valve. This part is used to control the flow of hot and cold water into the w...
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
In Stock
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Douglas
March 8, 2023
I replaced the control board. I went into diagnostic mode. I checked for error codes nothing. I did the recalibrate setup. Everything runs find till the final spin cycle. It then proceeds to fill the tub again with water.
For model number MVWC415EW1
Hello Douglas, thank you for reaching out. Checking out the following parts may help you get to the root of the problem: the drive belt, part number PS11747978, the drive hub kit, part number PS6012095, and the control board, part number PS12347407. We hope this information helps!
as soon as you plug the washer to power the pump comes on and will not go off
For model number MVWC415EW1
Hello Phil, thank you for getting in touch. We would recommend checking the control board, part number FIX12347407, to fix the issue. We hope this solves your problem!
Machine stopped working and humming like it was trying to pump out and spin ?We manually drain the machine and now it won’t fill.
For model number MVWC415EW1
Hello Bob, Thank you for your inquiry. Researching your model, we would recommend checking the water inlet valve, the lid lock switch and the water pressure level hose. We hope this helps.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.