Models
>
31EA-92KLN
31EA-92KLN Magic Chef Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Apr 6
This square burner grate has sides measuring approximately nine inches. It is all black in color.
No Longer Available
This safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range. This safety valve has an amperage range of 3.3 to 3.6 amps. The valv...
No Longer Available
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
This oven thermostat kit is to be used with gas oven models with a flat ignitor. Many thermostats do look similar. The knob has been updated by the manufacturer and may not look the same as the original.
No Longer Available
In Stock
Order now and your part arrives by Apr 6
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 31EA-92KLN
Viewing 3 of 3Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- peter from marine city, MI
- Parts Used:
- WP7501P133-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the oven igniter would glow but the gas wouldn't turn on
After removing the oven door, floor, and gas-jet diffuser plate, I could see the valve. There was a shield ov er the elec connections, which I removed. I turned off the gas line to the oven and elec power from the wall, then disconnected the valve. The orig valve had a mounting bracket which I swapped to the new valve( the holes lined up
... Read more
perfectly). I bolted everything back in place, turned it on, and the oven fired right up. I was afraid an appliance this old (1984) would no longer have any parts-availability. but PartSelect came through!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nicholas from livermore, CA
- Parts Used:
- 1430322
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gas burners and gas oven would not light
unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push
... Read more
on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Petaluma, CA
- Parts Used:
- WP7501P133-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Oven would not lite
With a little adjustment to the mount the part went in ok. Checked the oven works like new; well better than new.
Was this instruction helpful to you?
Thank you for voting!