Models > HA3000W

HA3000W ((PRE.B3533858)) Magic Chef Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Upper/Lower Bearing – Part Number: WP40004001
$56.59
Bearing only.
In Stock
Four Port Washer Pump with Metal Pulley – Part Number: 31968
The metallic pulley attached to this pump. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
V-Style Cogged Pump Belt (22.5 inches long) – Part Number: WP27155
$39.81
This V-style cogged tooth pump belt is used in conjunction with the drive belt in your washing machine. This belt is all black in color and is made entirely of rubber. It is twenty-two and a half inch...
Special Order
Two Speed Motor – Part Number: 27179P
This two speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the second speed. It runs at 1/2 horsepower and carries 115 volts. You can use this washer mo...
No Longer Available
KIT, IDLER – Part Number: R9900487
No Longer Available
DISCONTINUED – Part Number: 33521
No Longer Available
DISCONTINUED – Part Number: 27249
No Longer Available
DISCONTINUED – Part Number: 27602
$7.74
Special Order
DISCONTINUED – Part Number: 356P3
$155.24
Special Order
DISCONTINUED – Part Number: 208124
No Longer Available
DISCONTINUED – Part Number: 27120
No Longer Available
USE SPE 28918P – Part Number: 28918
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for HA3000W

Viewing 1 of 1
Will not drain
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kevin from Grayslake, IL
Parts Used:
31968, WP27155
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Washer stopped pumping discharge water
The only real problem was one spring loaded hose clamp to the rear of the pump. If it had been a standard clamp like the others I would have cut the repair time down by 2/3rd's. I did find that by removing one of the long wash drum springs, I then had more room to get my channellocks back there to get the stupid clamp to compress, and the n used a screw driver to push the clamp back off the the connecting port. I replaced the camp w/ a standard clamp and the reassembly went quick and easy. Note, If you replace the pump drive belt with a new one, you WILL have to adjust the belt tension after a few minutes use.
Read less
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from ROUND LAKE PK, IL
Parts Used:
WP27155
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
Water pump motor belt broke
It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CATHERINE from WEST CHESTER, PA
Parts Used:
31968
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
Water Pump Started Leaking
Removed the old pump and installed the new one, works great!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More