Models > 13AM77LS058

13AM77LS058 MTD Lawn Tractor

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 13AM77LS058

Viewing 35 of 35
Keep searches simple, eg. "belt" or "pump".
This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: ...
In Stock
This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread si...
In Stock
Genuine OEM replacement part, this item is sold individually. As the description says, this is the Steering Shaft for all of the Lawn Tractors shown below. One of the most popular reasons this part ...
In Stock
This is an OEM deck engagement cable, sold as one part. This part is for a lawnmower and its purpose is to engage the mowers blade, allowing you to control your engine zone. It consists of a metal wir...
In Stock
This is a manufacturer-approved replacement flange bearing for a lawn tractor. It is sold individually. The function of this part is to help secure the axle assembly to the pivot axle. It also allows ...
In Stock
$53.72
This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the p...
In Stock
This is a lock ball joint assembly for your lawn tractor. The ball joint assembly connects to the pitman arm and the drag link, and is a part of the steering mechanism on your machine. This part is 7/...
In Stock
Key
$18.33
In Stock
This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of ...
In Stock
In Stock
This part includes one hex flange nut that is compatible with various outdoor equipment. It has a thread of 5/8-18 and consists of a hex nut with a wide flange on one end. The flange works like a wash...
In Stock
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Laurie from RICHLANDS, NC
Parts Used:
731-05628
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set, Wrench (Adjustable), Wrench set
Oil Drain Sleeve
I wish this was longer...it's only about 6", barely enough to have the oil flow past the metal plate of the riding lawnmower. I'm going to figure out a way to make a permanent extension something like this video would be SO much better https://www.youtube.com/watch?v=G9ZVoeqr6R8&t=79s
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from TRIANGLE, VA
Parts Used:
954-04208A
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Wrench set
upper transmission belt cracked bad
Removed battery, then battery hanger brackets.
Removed the tension spring from under side of seat. That was a little tuff to do. put a long phillips screw driver through transmission pulley.
put a 7/8 box wrench on pulley nut and removed it. took old belt off and installed new one. Reversed order of removal.
Getting the t ension spring back into the bracket hole was a little tricky. I used a pair of long needle nose pliers to re install the spring.
cut my yard and I'm a happy camper !!!!!!!!!!!!!!!!!!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from eden, NC
Parts Used:
731-04949A
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Didn't line up very easy
Put one side in bottom first and you have to slightly twist the lens to get the other clips to pop in.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!