Models > 13AT604H755

13AT604H755 (2004) MTD Lawn Tractor

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This part contains one steering pinion gear for a lawn tractor. It is part of the steering mechanism and is highly prone to wear and tear. If this pinion gear becomes stripped it can cause steering to...
In Stock
This is a lock ball joint assembly for your lawn tractor. The ball joint assembly connects to the pitman arm and the drag link, and is a part of the steering mechanism on your machine. This part is 7/...
In Stock
Key
$18.33
In Stock
This part includes one hex flange bearing for a lawn tractor. It is sourced directly from the original manufacturer. Its purpose is to connect the steering shaft to the frame of the lawn tractor. It h...
In Stock
This part includes one hex flange nut that is compatible with various outdoor equipment. It has a thread of 5/8-18 and consists of a hex nut with a wide flange on one end. The flange works like a wash...
In Stock
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventua...
In Stock
This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit. Make s...
In Stock
This is a Belleville washer, and it is used with various lawn and garden equipment around your home. This part has an inner diameter of 0.340 inches and an outer diameter of 0.872 inches. The convex s...
In Stock
This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with...
In Stock
$28.38
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
TERRY from OAK CREEK, WI
Parts Used:
954-0468
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
LISA M from BATESVILLE, AR
Parts Used:
737-0300A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Mixer began to make a noise on speed two and higher
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do es not make the slight howl sound.
5 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Northville, NY
Parts Used:
941-0656A
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!