Models
>
LT2115J2115B-954130210
LT2115J2115B-954130210 (2004-06) Jonsered Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.55
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Aug 21
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Aug 21
$6.55
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Aug 21
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Aug 21
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Aug 21
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Aug 21
$18.65
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Aug 21
$6.55
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A ...
In Stock
Order now and your part arrives by Aug 21
$6.55
This is an authentic OEM bearing for lawn tractors and lawn mowers. Bearings provide a cushion for moving components, so they do not damage due to the constant rubbing against each other. They also he...
In Stock
Order now and your part arrives by Aug 21
$6.55
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
In Stock
Order now and your part arrives by Aug 21
$6.55
This is a genuine Craftsman replacement part for use in lawn tractors. It helps to connect the deflector rod to the deflector shield. The metal push nut is a small part and will need to be replaced if...
In Stock
Order now and your part arrives by Aug 21
$6.55
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tigh...
In Stock
Order now and your part arrives by Aug 21
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CEDAR SPRINGS, MI
- Parts Used:
- 532171888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The tie rod on my 20 year-old lawn tractor snapped.
I used two wrenches, unscrewed both ends of the old tie rod and it fell out. In nearly no time, I had the new one in. After finding the right end wrenches, I don't think I had more than 10 minutes into the project. Easiest repair I have done on anything in a long time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!