Models
>
96045004700
96045004700 Husqvarna Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 96045004700
Viewing 22 of 22
Keep searches simple, eg. "belt" or "pump".
$6.25
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Mar 20
In Stock
Order now and your part arrives by Mar 20
$6.25
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Mar 20
$6.25
This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in pl...
In Stock
Order now and your part arrives by Mar 20
$12.40
This genuine Craftsman hex gauge wheel is a replacement part sourced directly from the original manufacturer and is designed for use with riding lawn mowers. It attaches to the mower’s deck assembly a...
In Stock
Order now and your part arrives by Mar 20
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Mar 20
$6.25
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Mar 20
$12.50
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Mar 20
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Mar 20
$67.27
This mandrel assembly is for lawn tractors.
Mandrel assembly attaches to the mower deck and spins the blades. The assembly may include multiple parts; refer to your parts diagram for a complete lis...
In Stock
Order now and your part arrives by Mar 20
$31.34
It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply...
In Stock
Order now and your part arrives by Mar 20
$28.84
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
Order now and your part arrives by Mar 20
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 96045004700
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from CANBY, MN
- Parts Used:
- 587820301
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Worn out Mandrel Assemblies
Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from LAKEVILLE, MA
- Parts Used:
- 532439870
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Original shield was damaged
Removed original shield ( 2 bolts), replaced with new shield.
Was this instruction helpful to you?
Thank you for voting!