Models
>
917279060
917279060 Husqvarna Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 917279060
Viewing 11 of 11
Keep searches simple, eg. "belt" or "pump".
$6.55
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Sep 10
$6.55
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Sep 10
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Sep 10
$6.55
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Sep 10
$26.35
This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over ...
In Stock
Order now and your part arrives by Sep 10
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Sep 10
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Sep 10
$18.65
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Sep 10
$31.53
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
Order now and your part arrives by Sep 10
$28.55
This is mulching blade is specially designed for use with Craftsman riding lawn mowers/tractors. Mulching blades are shaped to keep the grass under deck for longer allowing it to be cut into smaller p...
In Stock
Order now and your part arrives by Sep 10
$6.55
Genuine Manufacturer Approved Carriage Bolt is a standard part that fits a variety of products. This part is sold individually and the Nut is not included. The square area under the head is designed t...
In Stock
Order now and your part arrives by Sep 10
$6.55
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A ...
In Stock
Order now and your part arrives by Sep 10
Common Problems and Symptoms for 917279060
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trace from LISLE, IL
- Parts Used:
- 532138971
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!