Models
>
96045005700
96045005700 Husqvarna Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 96045005700
Viewing 17 of 17
Keep searches simple, eg. "belt" or "pump".
$6.25
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Mar 21
$6.25
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Mar 21
$6.25
This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in pl...
In Stock
Order now and your part arrives by Mar 21
$12.50
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Mar 21
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Mar 21
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Mar 21
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Mar 21
$17.92
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Mar 21
$31.34
It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply...
In Stock
Order now and your part arrives by Mar 21
$28.84
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
Order now and your part arrives by Mar 21
$6.25
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A ...
In Stock
Order now and your part arrives by Mar 21
$6.25
This is an OEM bowtie cotter pin for lawn tractors. It is sold individually. This part is made of metal material, so over time, this metal can corrode or rust, especially if the lawn tractor is expose...
In Stock
Order now and your part arrives by Mar 21
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 96045005700
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 84001919
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from SAINT JO, TX
- Parts Used:
- 797242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Rod broke ruining the case and camshaft
dissembled ordered repair parts, piston ,upper case, rod, camshaft, seal kit, and motor maintenance CD
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mowe ... Read more r (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mowe ... Read more r (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from LAKEVILLE, MA
- Parts Used:
- 532439870
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Original shield was damaged
Removed original shield ( 2 bolts), replaced with new shield.
Was this instruction helpful to you?
Thank you for voting!