Models
>
XT2-SLX54
XT2-SLX54 ((131QA2CA010)(2018)) Cub Cadet Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: ...
In Stock
Order now and your part arrives by Nov 12
$6.51
This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread si...
In Stock
Order now and your part arrives by Nov 12
This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of ...
In Stock
Order now and your part arrives by Nov 12
$6.51
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
Order now and your part arrives by Nov 12
$6.55
This replacement screw is a genuine item that is sourced from original equipment manufacturer. It is a high quality hardware that is commonly used with walk-behind lawn mowers. This screw has multiple...
In Stock
Order now and your part arrives by Nov 12
$6.51
This item is a genuine OEM replacement part that is intended to be used with snowthrowers and lawnmowers from Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The metal hex head screw is us...
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
It is an authentic OEM sourced item which is specially produced for use with lawn mowers made by MTD, Bolens, Yard Man, Yard Machines, Troy-Bilt, and Cub Cadet. The flange lock nut attaches to the rea...
In Stock
Order now and your part arrives by Nov 12
$6.55
It is an authentic OEM supplied replacement push cap that is commonly utilized on riding lawn mowers and tractors. This is the push cap that is secured over the flange bearing, please make sure to che...
In Stock
Order now and your part arrives by Nov 12
NOTE: Battery is not charged and does not include electrolyte or acid.
No Longer Available
In Stock
Order now and your part arrives by Nov 12
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dean from DETROIT LAKES, MN
- Parts Used:
- 725-06173
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clutch harness had a broken wire. So needed a new harnesd
Jacked up front of the mower …went to pto clutch unplugged old harness has 2 quick disconnects and plugged in the new harness in the the connectors and started mower and it worked great. Took less than 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from LAKEWOOD, OH
- Parts Used:
- 710-04995A, 731-07487
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I replaced the deck on my Craftsman Lawn Mower, and needed a new water nozzle and some screws to hold the front wheel assembly on.
I removed the rear wheels, then I removed the blade, then the motor, then the front wheel assembly. The bolts holding the front wheel assembly were rusted and rounded trying to remove them, so I cut them out with a grinder. Afterwards I removed the remainder of the screw with a pair of pliers. I also removed the Water jet cleanout nozz
... Read more
le, found it was cracked, ordered the part from PartSelect, along with the screws needed to attach the front wheel assembly. I cleaned the remaining parts and re installed them onto the new deck. First, I installed the front wheel assembly, then the motor, then sat the mower upright, installed the blade, then took the rear wheel assembly and aligned it and fastened it to the deck. Last piece was the water nozzle. I placed it in the recess for it, and fastened it with the bolt. Then I tested the mower, and it worked without issue. Afterwards I used the new clean out port to rinse the underside of the deck, and it worked well.
Read less
Was this instruction helpful to you?
Thank you for voting!