Models
>
96046001600
96046001600 Ariens Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 96046001600
Viewing 18 of 18
Keep searches simple, eg. "belt" or "pump".
$6.51
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
$6.51
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Apr 10
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Apr 10
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Apr 10
$32.64
It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply...
In Stock
Order now and your part arrives by Apr 10
$30.03
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
Order now and your part arrives by Apr 10
$28.71
This is mulching blade is specially designed for use with Craftsman riding lawn mowers/tractors. Mulching blades are shaped to keep the grass under deck for longer allowing it to be cut into smaller p...
In Stock
Order now and your part arrives by Apr 10
$6.51
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A ...
In Stock
Order now and your part arrives by Apr 10
$6.51
This is an authentic OEM bearing for lawn tractors and lawn mowers. Bearings provide a cushion for moving components, so they do not damage due to the constant rubbing against each other. They also he...
In Stock
Order now and your part arrives by Apr 10
This is a genuine item that is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. The lift link attaches to the front of the mowe...
In Stock
Order now and your part arrives by Apr 10
$6.51
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tigh...
In Stock
Order now and your part arrives by Apr 10
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 96046001600
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Engine misfires
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 84001919
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Was this instruction helpful to you?
Thank you for voting!