Models
>
TB210
TB210 (12A-A26N211 2010) Troy-Bilt Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for TB210
Viewing 1 of 1_(2010)_WW_1.gif "Page A Diagram and Parts List for 12A-A26N211 2010 Troy-Bilt Lawn Mower")
Keep searches simple, eg. "belt" or "pump".
$30.64
This is a genuine OEM replacement part, it is sold individually.
This is the front wheel on the models shown below.
There are two of them on each mower.
The wheel has a ring gear on the inside whic...
On Order
$35.34
This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces alo...
In Stock
Order now and your part arrives by Apr 2
$25.20
Genuine OEM replacement part, this part is sold individually. This is the Side Discharge Chute for the lawn mowers listed below. It is mounted to the side of the mower for the cut grass to be expelled...
Special Order
$6.51
This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made o...
In Stock
Order now and your part arrives by Apr 2
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
Order now and your part arrives by Apr 2
$6.51
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
Order now and your part arrives by Apr 2
$67.61
8 x 2.125
This wheel is for lawn mowers.
Wear work gloves to protect your hands when installing this part.
Special Order
$59.91
This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is col...
In Stock
Order now and your part arrives by Apr 2
The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of meta...
In Stock
Order now and your part arrives by Apr 2
In Stock
Order now and your part arrives by Apr 2
In Stock
Order now and your part arrives by Apr 2
$6.51
This is a genuine OEM sourced replacement part is designed for use with walk behind/push lawn mowers. This hinge pin is an important part of a mechanism which allows users to secure the mulch door or ...
In Stock
Order now and your part arrives by Apr 2
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for TB210
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jay from GERRY, NY
- Parts Used:
- 734-04018C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Not the exact fit
I had to drill and tap the ends of the axle and put a 1/4” bolt in to fasten the wheels. The hubs were not the same. They fastened differently.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WAYNE, MI
- Parts Used:
- 734-04018C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Front drive wheels were wore out
Unbolted old wheels and bolted new wheels to my lawn mower
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from LA CRESCENT, MN
- Parts Used:
- 753-06703
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
rear axel assembly needed replacement due to broken wheel height lever
Removed rear wheels, cut the old axel of with a sawsall and pulled the assembly out as I didn't want chance breaking the plastic retaining tabs as they can become brittle from age. Break the tabs and you have nothing to hold the new axel assembly in place.
Snapped the new assembly in place and put the wheels back on.
Snapped the new assembly in place and put the wheels back on.
Was this instruction helpful to you?
Thank you for voting!