Models
>
12A-466A711
12A-466A711 (2005) Troy-Bilt Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 12A-466A711
Viewing 1 of 1_WW_1.gif "Page A Diagram and Parts List for 2005 Troy-Bilt Lawn Mower")
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM replacement part, it is sold individually.
This is the front wheel on the models shown below.
There are two of them on each mower.
The wheel has a ring gear on the inside whic...
No Longer Available
$32.37
This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces alo...
In Stock
$5.84
This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made o...
In Stock
In Stock
In Stock
In Stock
$4.99
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
8 x 2.125
This wheel is for lawn mowers.
Wear work gloves to protect your hands when installing this part.
No Longer Available
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 12A-466A711
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from MIDVALE, OH
- Parts Used:
- 946-1132, 747-1161A-0637
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cable was frozen and bail was broken
I removed the bail and removed cable from motor! Then it was ready for new parts installation!
I attached the cable to the motor and I put the right side of bail in its hole and I then installed cable into the bail and then installed the left side of bail into its hole!! Once that was completed I used two zip ties to cinch down cab ... Read more le to the handle!! Job done!
I attached the cable to the motor and I put the right side of bail in its hole and I then installed cable into the bail and then installed the left side of bail into its hole!! Once that was completed I used two zip ties to cinch down cab ... Read more le to the handle!! Job done!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Kennewick, WA
- Parts Used:
- 734-04018C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The treads on the front drive wheels were worn down to the point that they provided little traction.
Removed a single nut on each end of the drive shaft with the appropriate socket. Wheels then slipped off. Cleaned/polished the shaft with fine sandpaper, lubed with silicone spray, slid on the wheels and reinstalled the nuts with the same socket. Wheels were an exact fit and OEM quality. Done in 15 minutes start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WAYNE, MI
- Parts Used:
- 734-04018C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Front drive wheels were wore out
Unbolted old wheels and bolted new wheels to my lawn mower
Was this instruction helpful to you?
Thank you for voting!