Models
>
21764
21764 (410000000 - 999999999) Toro Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 21764
Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
$6.55
This is an Original Manufacturer Sourced Stepped Washer used on a variety of Push Lawn Mowers. This is the Metal Washer that fits with Rear or Front Wheel Cover depending on the model. It helps secure...
In Stock
Order now and your part arrives by Jul 30
$6.55
This part includes one ball bearing for a lawn mower. This official OEM replacement part is designed to minimize friction between components that rotate. They help to reduce the amount of wear put on ...
In Stock
Order now and your part arrives by Jul 30
$6.55
Genuine Manufacturer Approved replacement part designed for use with some Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. Bolt is 3/8-16 X 3-5/8. It is commonly ...
In Stock
Order now and your part arrives by Jul 30
$6.55
This is a genuinely made torsion spring, sold as an individual part. It is part of the handle assembly and attaches to the end of the control bar, allowing it to retract. This metal spring can rust, s...
In Stock
Order now and your part arrives by Jul 30
$21.95
This is a side discharge chute for a lawn mower. It is a genuinely sourced part and is sold individually. Please note that the hinge bracket assembly and spring used to secure this side deflector is n...
In Stock
Order now and your part arrives by Jul 30
$18.90
This is a Genuine Manufacturer Approved replacement part used on Toro Snowthrowers. This Ball Bearing has multiple applications in the Snowthrowers. This part is made out of Metal and it is Sold Indiv...
In Stock
Order now and your part arrives by Jul 30
On Order
$46.15
This authentic replacement traction cable is supplied directly from original equipment manufacturer for use on Toro lawn mowers. The traction cable engages drive wheels on the lawn mowers. It is conne...
In Stock
Order now and your part arrives by Jul 30
$7.04
This item has been OEM sourced an is intended to be used with walk-behind lawnmowers from Toro and Lawn Boy. The metal pinion gear attaches the mower\\\'s transaxle and is used to interconnect with th...
In Stock
Order now and your part arrives by Jul 30
$6.55
This item is an authentic Toro replacement part that has been OEM sourced to be used with walk-behind lawnmowers. The plastic cable guide attaches to the handle assembly and is used to keep the contro...
In Stock
Order now and your part arrives by Jul 30
$26.35
It is an authentic part that is supplied by the original manufacturer. The assembly is utilized on Lawn Boy and Toro lawn mowers. The switch provides a user with an ability to turn off the engine. Ove...
In Stock
Order now and your part arrives by Jul 30
$41.75
This is a genuine Toro part to be used in walk-behind lawn mowers. The cable-brake attaches to the handle control and engages or disengages the mower blade. It may become detached or broken and can be...
In Stock
Order now and your part arrives by Jul 30
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ray from YARDLEY, PA
- Parts Used:
- 105-1809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Was this instruction helpful to you?
Thank you for voting!