Models
>
21026
21026 (400000-) Toro Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
This authentic component is an OEM part which is designed for use with Toro snowthrowers. It helps to secure a part on a shaft. This is an identical replacement for a damaged or a faulty hardware that...
In Stock
Order now and your part arrives by Apr 10
$8.38
This is a Genuine OEM Toro Pinion Gear, with 15 teeth, which drives the gear on the wheel. This part is sold individually. There are two of these gears used on the Mowers for the left and right sides....
In Stock
Order now and your part arrives by Apr 10
$6.51
This is a Genuine Toro replacement part used on a variety of Walk Behind/Push Mowers. This is a Metal Half Moon Key and it is sold individually. The key helps to secure drive wheels to the Transmission Axle.
On Order
$6.51
This is a Genuine OEM replacement part used on Toro Lawn Mowers. This is a Metal Spring and it is Sold Individually. The spring moves the key up and down. When the key moves down on the drive axle you...
In Stock
Order now and your part arrives by Apr 10
$6.51
This is a genuine OEM sourced replacement part designed for use with lawn mowers. This thrust washer helps to secure the pinion gear. It helps to distribute the pressure evenly and provides a tight se...
In Stock
Order now and your part arrives by Apr 10
$6.51
This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it bec...
In Stock
Order now and your part arrives by Apr 10
$6.84
This replacement cap-fuel is a genuine OEM supplied item, not an aftermarket imitation. It is a high quality part commonly used on Murray and Toro snow throwers and lawn mowers. It is used to keep the...
In Stock
Order now and your part arrives by Apr 10
$9.13
This is a filter cartridge for the air filter in various lawn equipment. The filter removes dirt, dust, and other debris from entering the carburetor, and contaminating the engine. If the engine in yo...
In Stock
Order now and your part arrives by Apr 10
$11.22
This is a genuine manufacturer-sourced component which is specially designed for use with Toro walk-behind lawn mowers. It is the lever that helps to secure the tractions control bar, please make sure...
In Stock
Order now and your part arrives by Apr 10
$24.70
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of r...
In Stock
Order now and your part arrives by Apr 10
$6.51
This screw is an authentic OEM sourced hardware, it is not an aftermarket imitation. It is commonly utilized on Toro snow throwers. It is a standard hardware which has multiple uses depending on your ...
In Stock
Order now and your part arrives by Apr 10
$12.86
This is an OEM part directly sourced from the manufacturer for lawn mowers made by Toro and Lawn Boy. The plain washer goes next to the shift collar and is made out of metal. A screwdriver, a set of p...
In Stock
Order now and your part arrives by Apr 10
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 21026
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Engine will not idle
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Seikai from MARICOPA, CA
- Parts Used:
- 497680
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel
... Read more
, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from BANGOR, ME
- Parts Used:
- 590508
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench set
Leaking gaskets
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
Was this instruction helpful to you?
Thank you for voting!
blower housing on the customers log splitter broke.
blower housing on my brothers log splitter broke at the anchor points and caused the pull start to break and come apart. I was able to buy the parts and fix the log splitter for half the price of a new motor, saving him about $300.00.
Was this instruction helpful to you?
Thank you for voting!