12BVB15R799 MTD Lawn Mower - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from LAKEWOOD, OH
- Parts Used:
- 710-04995A, 731-07487
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I replaced the deck on my Craftsman Lawn Mower, and needed a new water nozzle and some screws to hold the front wheel assembly on.
I removed the rear wheels, then I removed the blade, then the motor, then the front wheel assembly. The bolts holding the front wheel assembly were rusted and rounded trying to remove them, so I cut them out with a grinder. Afterwards I removed the remainder of the screw with a pair of pliers. I also removed the Water jet cleanout nozzle, found it was cracked, ordered the part from PartSelect, along with the screws needed to attach the front wheel assembly. I cleaned the remaining parts and re installed them onto the new deck. First, I installed the front wheel assembly, then the motor, then sat the mower upright, installed the blade, then took the rear wheel assembly and aligned it and fastened it to the deck. Last piece was the water nozzle. I placed it in the recess for it, and fastened it with the bolt. Then I tested the mower, and it worked without issue. Afterwards I used the new clean out port to rinse the underside of the deck, and it worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laird from North Las Vegas, NV
- Parts Used:
- 592172
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Bought Troy Built pressure Washer at garage Sale for $30.00 leaked fuel
I have a solid understanding of small engines. This pressure washer was used twice in 2013, when purchased. Sat in a garage for a couple of years with gas in tank and carburetor. Owner was moving and after 7 years of moving it around he sold it at a garage sale.
I took it home and took off gas tank and thoroughly cleaned it. Then went through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
I took it home and took off gas tank and thoroughly cleaned it. Then went through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from KENNER, LA
- Parts Used:
- 796503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw in new dipstick, check oil level
Very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NIXA, MO
- Parts Used:
- 720-05066A
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Lost wing knob and nut that holds the handle onto the mower
Can't do the repair. You sent me the two wing knobs I ordered, but no nuts. No one sells the nuts. I've driven all over trying to find them. Wasted my money and a lot of time. Zip ties are holding the handle on. I sent an email to customer service asking for the nuts, never heard a word from anyone. Another great example of how not to run a business.
Was this instruction helpful to you?
Thank you for voting!