Models
>
22243
22243 Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for 22243
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
$6.51
This authentic component is an OEM part which is designed for use with Toro snowthrowers. It helps to secure a part on a shaft. This is an identical replacement for a damaged or a faulty hardware that...
In Stock
Order now and your part arrives by Oct 8
$6.55
This is an Original Manufacturer Sourced Stepped Washer used on a variety of Push Lawn Mowers. This is the Metal Washer that fits with Rear or Front Wheel Cover depending on the model. It helps secure...
In Stock
Order now and your part arrives by Oct 8
$6.55
This is a nut, for a variety of outdoor lawn equipment. This part is a nylon insert locking nut, meaning it has a nylon collar insert that makes the nut resistant to turning from heavy vibrations. It ...
In Stock
Order now and your part arrives by Oct 8
$6.55
This is an authentic manufacturer sourced replacement part designed for use with Toro walk-behind lawn mowers. This part helps to secure the mower wheel, allowing it to rotate freely. It is made out o...
In Stock
Order now and your part arrives by Oct 8
$6.51
It is an authentic Toro hardware. The thrust washer is supplied from the original equipment manufacturer for use on lawn mowers. It is utilized to provide a tight fit between connected components of t...
In Stock
Order now and your part arrives by Oct 8
$6.55
This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it bec...
In Stock
Order now and your part arrives by Oct 8
$6.51
It is an authentic Toro hardware. The washer-clutch is supplied from the original equipment manufacturer for use on lawn mowers. It helps to engage the pinion gear which is an important component that...
In Stock
Order now and your part arrives by Oct 8
$6.55
This friction ring is an authentic item which is supplied by the original manufacturer for Toro lawn mowers. It is one of the special parts that helps to provide a tight seal between components. Over ...
In Stock
Order now and your part arrives by Oct 8
$6.51
This item is an authentic Toro replacement part that has been sourced from the original manufacturer to be used with walk-behind lawnmowers. The metal washer is used to provide spacing between the whe...
In Stock
Order now and your part arrives by Oct 8
$15.35
The metal pinion is an authentic Toro part that has been sourced from the original manufacturer to be used with lawnmowers. This item attaches to the transmission axle and interconnects with the drive...
In Stock
Order now and your part arrives by Oct 8
This is a screw for your lawn equipment. Most commonly used to secure the half-rotor to the blade in your machine. This part is a hex bolt, and requires a nut or a tapped hole.
In Stock
Order now and your part arrives by Oct 8
$6.55
This genuine replacement part is supplied from original equipment manufacturer. It is a commonly used item on Toro lawn mowers. The purpose of this shoulder bolt is to secure a wheel to the axle. This...
In Stock
Order now and your part arrives by Oct 8
Common Problems and Symptoms for 22243
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Engine will not idle
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Seikai from MARICOPA, CA
- Parts Used:
- 497680
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel
... Read more
, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from BANGOR, ME
- Parts Used:
- 590508
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench set
Leaking gaskets
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
Was this instruction helpful to you?
Thank you for voting!