Models
>
53
53 (ROYAL) Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.55
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Jul 23
In Stock
Order now and your part arrives by Jul 23
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually...
In Stock
Order now and your part arrives by Jul 23
$6.55
This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in pl...
In Stock
Order now and your part arrives by Jul 23
$13.15
This genuine Craftsman hex gauge wheel is a replacement part sourced directly from the original manufacturer and is designed for use with riding lawn mowers. It attaches to the mower’s deck assembly a...
In Stock
Order now and your part arrives by Jul 23
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Jul 23
$12.05
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Jul 23
$38.39
This is a genuine OEM replacement part, sold individually. V-belt drive systems, also called friction drives (because power is transmitted as a result of the belt's adherence to the pulley) transmit ...
In Stock
Order now and your part arrives by Jul 23
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Jul 23
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Jul 23
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Jul 23
$18.65
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Jul 23
Common Problems and Symptoms for 53
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynn from BOILING SPGS, PA
- Parts Used:
- 592855201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Drive belt came off from transaxle pulley, noticed in bad shape, ordered new one form parts select.
The drive belt literally goes from the back of the tractor to the front. The mower must be removed, helps to have the tractor up on blocks to give adequate room for work on underside. Belt goes easiest on the engine first, then thread to the rear, install on the rear, (driven pulley) then on the idlers. Check to assure that it function
... Read more
s properly before re-installing the mower. If you have the owners manual, there is a diagram, (check your orientation, it is not clear if it is a birdseye or under tractor view) which offered some help. When replacing belt, check the transaxle front mount, mine was broken which is why the belt came off in the first place. Repairing the mount was quite a job in itself, but now works fine.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from CANBY, MN
- Parts Used:
- 587820301
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Worn out Mandrel Assemblies
Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from PENNSBURG, PA
- Parts Used:
- 587686701
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Right axle bent
Replacing belt with no problem. I've ordered the front right axle spindle assembly three times. This is from your parts list and you sent me the part and they did not work at all.
Was this instruction helpful to you?
Thank you for voting!