Models
>
YTH21K46
YTH21K46 ((96045002101)(2010-06)) Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for YTH21K46
Viewing 10 of 10Keep searches simple, eg. "belt" or "pump".
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
On Order
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
Special Order
On Order
$14.93
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
This is an OEM bowtie cotter pin for lawn tractors. It is sold individually. This part is made of metal material, so over time, this metal can corrode or rust, especially if the lawn tractor is expose...
On Order
$13.69
This is a flat idler pulley, approved by the manufacturer for use in lawn tractors. The pulley provides tension to the belt. For this DIY repair you will need a wrench and pliers. You will start by re...
In Stock
This ground drive fixed idler pulley is for lawn tractors.
910 inch offset
Ground drive fixed idler pulley helps apply tension to the drive belt, allowing the belt to turn.
Wear work gloves to...
On Order
This is a 5/16-inch metal cotter pin and it is sold as an individual part. Cotter pins secure a variety of different assemblies by placing them through a drilled hole in a shaft or bolt, such as on a ...
In Stock
In Stock
On Order
This part includes one genuinely sourced washer for a ride-on lawn mower. Washers help to disperse the load and provides a tight seal in between components. Depending on your unit, the applications wi...
In Stock
$6.21
This part includes one clear zinc washer. It is sourced directly from the original manufacturer and is an exact replacement for the original part. The function of this part is to distribute weight eve...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for YTH21K46
Viewing 2 of 2Drive system does not work
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynn from BOILING SPGS, PA
- Parts Used:
- 532130969
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Drive belt came off from transaxle pulley, noticed in bad shape, ordered new one form parts select.
The drive belt literally goes from the back of the tractor to the front. The mower must be removed, helps to have the tractor up on blocks to give adequate room for work on underside. Belt goes easiest on the engine first, then thread to the rear, install on the rear, (driven pulley) then on the idlers. Check to assure that it function
... Read more
s properly before re-installing the mower. If you have the owners manual, there is a diagram, (check your orientation, it is not clear if it is a birdseye or under tractor view) which offered some help. When replacing belt, check the transaxle front mount, mine was broken which is why the belt came off in the first place. Repairing the mount was quite a job in itself, but now works fine.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!