Models
>
HU775H-96145000700
HU775H-96145000700 Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HU775H-96145000700
Viewing 12 of 12
Keep searches simple, eg. "belt" or "pump".
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Apr 6
$17.20
This is a single black plastic clipping deflector, also sometimes referred to as a discharge chute, for a lawn mower. This part attaches to the mulcher door on the side of the lawnmower deck. It is re...
In Stock
Order now and your part arrives by Apr 6
$11.49
This is an OEM part sourced directly from Husqvarna. This handle knob is used on a variety of lawn and garden equipment. Commonly used in lawn mower to secure the handle, and in snow blowers to secure...
In Stock
Order now and your part arrives by Apr 6
This is an OEM part sourced directly from Husqvarna. This grade 8 hex head screw is made of metal and measures approximately 3/8 - 24 x 1 ? 3/8. This screw is commonly used in lawn mowers, snow blower...
In Stock
Order now and your part arrives by Apr 6
$21.52
This Genuine OEM blade adapter is a manufacturer-sourced replacement part designed for use with select Craftsman lawn mowers. Made from durable metal and sold individually, this component serves as a ...
In Stock
Order now and your part arrives by Apr 6
$8.70
This manufacturer approved bolt is made for lawn and garden equipment. In conjunction with handle knob it helps to secure the upper and lower handles together. The way this bolt is designed, you will ...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on y...
In Stock
Order now and your part arrives by Apr 6
$6.51
This e-ring is an original part from Craftsman for lawn mowers and walk behind lawn mowers. This part tightens the pinion gear to the front axle drive. It is recommended that you wear gloves before in...
In Stock
Order now and your part arrives by Apr 6
$30.03
This genuine OEM replacement blade is designed for Husqvarna walk-behind and push lawn mowers with a 22-inch deck. Measuring 21-1/2 inches, this 4-in-1 multipurpose blade combines the features of a hi...
In Stock
Order now and your part arrives by Apr 6
$7.16
This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the ...
In Stock
Order now and your part arrives by Apr 6
$63.68
This is an authentic manufacturer made replacement part which is specially designed for use with Husqvarna lawn mowers. The grass bag collects grass clippings that are cut by the blade, making disposa...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is a genuine OEM sourced replacement part commonly used on lawn and garden equipment. This specially designed lock nut resists loosening when it is properly threaded onto a bolt. It is has multip...
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laird from North Las Vegas, NV
- Parts Used:
- 592172
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Bought Troy Built pressure Washer at garage Sale for $30.00 leaked fuel
I have a solid understanding of small engines. This pressure washer was used twice in 2013, when purchased. Sat in a garage for a couple of years with gas in tank and carburetor. Owner was moving and after 7 years of moving it around he sold it at a garage sale.
I took it home and took off gas tank and thoroughly cleaned it. Then we ... Read more nt through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
I took it home and took off gas tank and thoroughly cleaned it. Then we ... Read more nt through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from SARASOTA, FL
- Parts Used:
- 596409
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The exhaust system just fell off the motor
I ordered the parts as there were only three screws and two bolts that needed to come out and then thenew ones go back in. Everything went just as planned...….well except the two bolts that where included by Briggs and Stratton appear to be 1/8-1/4" too short and now both of the threaded holes in the engine are now stripped and the quick
... Read more
easy repair is now a bust and not repairable by me.
This has nothing to do with PartSelect.com as they just shipped the Briggs and Stratton part box.
This has nothing to do with PartSelect.com as they just shipped the Briggs and Stratton part box.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ROSEBURG, OR
- Parts Used:
- 581473301
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Multi rounded pins worn off where the blade turned very little with th mower running.
Once the blade was off, the blade adapter came off easily with a little help from WD40, and getting the new one on was simple with a few taps with a plastic hammer
Was this instruction helpful to you?
Thank you for voting!