Models
>
954000512
954000512 Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually...
In Stock
Order now and your part arrives by Jul 20
$6.55
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Jul 20
$6.55
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Jul 20
$38.39
This is a genuine OEM replacement part, sold individually. V-belt drive systems, also called friction drives (because power is transmitted as a result of the belt's adherence to the pulley) transmit ...
In Stock
Order now and your part arrives by Jul 20
$26.35
This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over ...
In Stock
Order now and your part arrives by Jul 20
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Jul 20
$18.65
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Jul 20
$26.35
This is an authentically sourced OEM mandrel pulley, designed for lawn tractors (riding mowers) with a 42-inch deck. It is sold individually. This durable metal part measures approximately 5-3/16-inch...
In Stock
Order now and your part arrives by Jul 20
$6.55
Genuine Manufacturer Approved Carriage Bolt is a standard part that fits a variety of products. This part is sold individually and the Nut is not included. The square area under the head is designed t...
In Stock
Order now and your part arrives by Jul 20
$6.55
This is an authentic OEM bearing for lawn tractors and lawn mowers. Bearings provide a cushion for moving components, so they do not damage due to the constant rubbing against each other. They also he...
In Stock
Order now and your part arrives by Jul 20
$6.55
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
In Stock
Order now and your part arrives by Jul 20
$6.55
This is a genuine Craftsman replacement part for use in lawn tractors. It helps to connect the deflector rod to the deflector shield. The metal push nut is a small part and will need to be replaced if...
In Stock
Order now and your part arrives by Jul 20
Common Problems and Symptoms for 954000512
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynn from BOILING SPGS, PA
- Parts Used:
- 592855201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Drive belt came off from transaxle pulley, noticed in bad shape, ordered new one form parts select.
The drive belt literally goes from the back of the tractor to the front. The mower must be removed, helps to have the tractor up on blocks to give adequate room for work on underside. Belt goes easiest on the engine first, then thread to the rear, install on the rear, (driven pulley) then on the idlers. Check to assure that it function
... Read more
s properly before re-installing the mower. If you have the owners manual, there is a diagram, (check your orientation, it is not clear if it is a birdseye or under tractor view) which offered some help. When replacing belt, check the transaxle front mount, mine was broken which is why the belt came off in the first place. Repairing the mount was quite a job in itself, but now works fine.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trace from LISLE, IL
- Parts Used:
- 532138971
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!