Models
>
954170055
954170055 Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.25
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Mar 21
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually...
In Stock
Order now and your part arrives by Mar 21
$6.25
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Mar 21
$6.25
This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in pl...
In Stock
Order now and your part arrives by Mar 21
$12.40
This genuine Craftsman hex gauge wheel is a replacement part sourced directly from the original manufacturer and is designed for use with riding lawn mowers. It attaches to the mower’s deck assembly a...
In Stock
Order now and your part arrives by Mar 21
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Mar 21
$6.25
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Mar 21
$12.50
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Mar 21
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Mar 21
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Mar 21
$28.84
This is an OEM replacement part, sold individually. The High Lift Blade is also referred to as a 2 in 1 blade. It throws the clippings better, and is used when you are just discharging or bagging the...
In Stock
Order now and your part arrives by Mar 21
$17.92
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Mar 21
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hickory, NC
- Parts Used:
- 532177968
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Lound deck noise when mower put into motion
Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut c
... Read more
ame off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!