Models
>
RZ3016BF
RZ3016BF Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Apr 9
$13.02
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Apr 9
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Apr 9
$18.66
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Apr 9
$70.05
This mandrel assembly is for lawn tractors.
Mandrel assembly attaches to the mower deck and spins the blades. The assembly may include multiple parts; refer to your parts diagram for a complete lis...
In Stock
Order now and your part arrives by Apr 9
$6.51
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A ...
In Stock
Order now and your part arrives by Apr 9
$6.51
This is a genuine Craftsman replacement part for use in lawn tractors. It helps to connect the deflector rod to the deflector shield. The metal push nut is a small part and will need to be replaced if...
In Stock
Order now and your part arrives by Apr 9
$6.51
This is a single OEM replacement screw for a lawn mower. This flanged hex head screw measures 1/4-20 by 5/8. It is used in various applications, so we recommend checking the diagram related to your mo...
In Stock
Order now and your part arrives by Apr 9
This is a Manufacturer Approved replacement part designed for Riding Mowers/Lawn Tractors. Lift link attaches to the front of the mower deck and to the bracket under the front axle. The purpose of it ...
In Stock
Order now and your part arrives by Apr 9
$10.03
This is an authentic OEM part for use with Craftsman Lawn Tractors. The deck washout port attaches to the deck and washes grass and debris from under the deck. It is made out of metal and it is sold i...
In Stock
Order now and your part arrives by Apr 9
$32.64
This is an OEM sourced replacement ignition switch. It is commonly used on a variety of riding lawn mowers/tractors. Switch plays an important role because it allows user to easily start the mower usi...
In Stock
Order now and your part arrives by Apr 9
$8.70
This is a genuine replacement part sourced directly from manufacturer. It is designed for use with riding lawn mowers/tractors. The ignition key is inserted into the switch to start the mower. This is...
In Stock
Order now and your part arrives by Apr 9
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from Taylor, MI
- Parts Used:
- 532419274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
bent mower blade
it was a 5 minute job all I did was jack up the rear of the mower lay down along side of it and install the new blade tighten up the bolt then I lower the mower back down to the ground the started up the mower for a test run of the blade. and it works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from CANBY, MN
- Parts Used:
- 587820301
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Worn out Mandrel Assemblies
Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.
Was this instruction helpful to you?
Thank you for voting!