Models
>
14AJ808H101
14AJ808H101 (( 1H019H - 1H310H)) Cub Cadet Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$10.32
This part contains one steering pinion gear for a lawn tractor. It is part of the steering mechanism and is highly prone to wear and tear. If this pinion gear becomes stripped it can cause steering to...
In Stock
In Stock
$4.99
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
$4.99
This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventua...
In Stock
In Stock
$37.66
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
In Stock
In Stock
$26.91
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
In Stock
In Stock
$4.99
This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with...
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 14AJ808H101
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 796232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from OAK CREEK, WI
- Parts Used:
- 954-0468
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
Was this instruction helpful to you?
Thank you for voting!