Models > 13BD608G101

13BD608G101 (( 1H019H - 1H310H)) Cub Cadet Lawn Mower

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Steering Pinion Gear – Part Number: 717-1554
$10.32
This part contains one steering pinion gear for a lawn tractor. It is part of the steering mechanism and is highly prone to wear and tear. If this pinion gear becomes stripped it can cause steering to...
In Stock
Seal--Oil (PTO Side) – Part Number: 795387
$7.88
On Order
Plastic Bushing .380 ID – Part Number: 941-0475
$4.99
This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventua...
In Stock
TT Screw 1/4-20 x 0.5 – Part Number: 710-0599
$4.99
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
Connector-Hose – Part Number: 692317
$7.06
In Stock
Gasket--Exhaust – Part Number: 692236
$5.71
In Stock
Shoulder Screw # 12 -24 – Part Number: 710-1650
$4.99
In Stock
Gear-Pinion (Plastic and Aluminum Ring Gear) – Part Number: 695708
$7.18
In Stock
Crankcase Gasket With Bolts – Part Number: 594195
$37.66
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
In Stock
Armature-Magneto – Part Number: 591459
$58.83
In Stock
Clamp-Hose – Part Number: 791850
$4.99
In Stock
Motor Starter – Part Number: 593934
$143.85
This authentic manufacturer sourced replacement part is designed for use with lawn and garden engines. The starter motor provides an initial motion, engage the flywheel to start the engine. This start...
In Stock
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 13BD608G101

Viewing 1 of 1
Engine misfires
Fixed by these parts
Fixing
How to fix it
Replacing the Extension Spring,.62 X 6.12

Replacing the Extension Spring,.62 X 6.12

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
D from HUNTSVILLE, AL
Parts Used:
796232
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
rodney from MUSCATINE, IA
Parts Used:
594195, 795387, 793338
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
12 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
TERRY from OAK CREEK, WI
Parts Used:
954-0468
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More