Models
>
12A-979I100
12A-979I100 (2002) Cub Cadet Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
This is an OEM primer bulb and clip. It is attached to the engine air filter base. When the primer bulb is pushed, this fills the carburetor with fuel, making it easier to start a cold engine. This ru...
In Stock
Order now and your part arrives by Apr 23
$9.06
Genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. This item includes the seat. The needle valve opens and closes to control the flow of fuel into the carbure...
In Stock
Order now and your part arrives by Apr 23
$25.98
This manufacturer approved recoil starter pulley is designed for lawn and garden equipment engines. The recoil starter engages the drive cup on the flywheel to start the engine when pulled. This assem...
In Stock
Order now and your part arrives by Apr 23
$8.00
This part is the replacement gasket for the crankcase on your engine. The gasket helps to create a seal on the crankcase and prevent leaks. If you notice that your engine is not running at peak perfor...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recom...
In Stock
Order now and your part arrives by Apr 23
This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a...
In Stock
Order now and your part arrives by Apr 23
This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bo...
No Longer Available
$6.51
This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note s...
On Order
$18.04
This replacement part is designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to filter out dust and debris from contaminating engine and carburetor. Th...
In Stock
Order now and your part arrives by Apr 23
$79.61
This fuel tank is for lawn and garden equipment engines.
Fuel tank holds the gas that's needed by the engine.
Work in a well-ventilated area when installing this part. Drain the existing fuel f...
In Stock
Order now and your part arrives by Apr 23
$13.29
This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plas...
On Order
$4.15
This is a genuine replacement part sourced directly from the manufacturer. The hex jam nut is commonly found in MTD lawn tractors and edgers. This part is made of metal, and may be found in various ...
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 12A-979I100
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Seikai from MARICOPA, CA
- Parts Used:
- 497680
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel
... Read more
, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from ELDORA, IA
- Parts Used:
- 790120
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
slow delivery
I paid extra to get the item . Received a delivery date, a couple days before date ,received notification it was going and in California and delivery would be another week. Immediately I ordered the carburator from another supplier and received it three days before parts select came in. It was installed and used AND with NO SHIPPING CHARG
... Read more
ES>
I returned parts select item for refund. WILL NEVER EVER ORDER FROM THEM AGAIN and I paid extra for shipping which I will not get back. Poor service and they still blame delivery on pandemic, NO ONE ELSE seems to have that PROBLEM,.Vincent K
I returned parts select item for refund. WILL NEVER EVER ORDER FROM THEM AGAIN and I paid extra for shipping which I will not get back. Poor service and they still blame delivery on pandemic, NO ONE ELSE seems to have that PROBLEM,.Vincent K
Read less
Was this instruction helpful to you?
Thank you for voting!