Models
>
11065202311
11065202311 Kenmore Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 11065202311
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$108.02
This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.
In Stock
Order now and your part arrives by Apr 23
$7.60
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Apr 23
$60.49
This push to start switch is an authentic OEM replacement part for your dryer. Once a setting has been selected on the timer, the switch is then used to complete the circuit and start the cycle. If yo...
In Stock
Order now and your part arrives by Apr 23
This insert is sold individually. Knob not included. Knob is sold separately.
In Stock
Order now and your part arrives by Apr 23
$55.18
This lint filter screen has a white handle. This filter collects lint as it passes through the dryer vent.
In Stock
Order now and your part arrives by Apr 23
$60.49
This switch allows you to change the cycle settings on your dryer.
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 11065202311
Viewing 3 of 3Timer Not Working
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Josh from Emory, TX
- Parts Used:
- WPW10117655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Push to Start switch burned out due to electrical problem
Unplug from the wall ,remove upper back panel ( watch out for the grounding wire screwed to the panel), pulled off front knob, then twist and pull the switch out. Unplug the burned out switch, plugged in the new one. Re-assembled what I took apart, plugged her up and dried the load that was in the washer. Note: if yours is burned out due
... Read more
to house power surge make sure the timer is working after you replace the switch, you might need one of thoes too.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from CRUGER, MS
- Parts Used:
- WPW10185982
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer would not heat
Repair was very easy only took about ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katharine from Palm Springs, CA
- Parts Used:
- W10874409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The lint filter was seriously damaged
After the new filter arrived, I took the old filter out, put the newe one in. No tools, no difficulty at all. Actually, the really difficult part of this entire episode was finding the model number on the dryer. It was on the underside of the door.
Was this instruction helpful to you?
Thank you for voting!