Models
>
GI15NDXTB3
GI15NDXTB3 Whirlpool Ice Maker
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GI15NDXTB3
Viewing 6 of 6Manuals & Guides for GI15NDXTB3
Click to downloadKeep searches simple, eg. "belt" or "pump".
$36.12
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may...
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
$75.62
This part monitors the temperature and sends the readings to the electronic control board.
In Stock
Order within the next 4 hrs and your part ships today!
$60.72
There is approximately 10'of wire.
Note:2 kits are needed to replace both directions.
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
This is an ice cutter grid assembly for your ice maker. If your machine is not producing ice properly, the assembly may need replacing. You will find this part in the main unit of the ice maker. The t...
In Stock
Order within the next 4 hrs and your part ships today!
On Order
In Stock
Order within the next 4 hrs and your part ships today!
$67.84
This part is a drain pump for your ice maker. When you flush the reservoir on your ice maker to remove impurities, the drain pump is the part that removes the water from the reservoir. This is an auth...
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
$5.42
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
In Stock
Order within the next 4 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GI15NDXTB3
Viewing 5 of 5Light not working
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randy from Hays, KS
- Parts Used:
- WP2149705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken light switch
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps
... Read more
) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from North Wilkesboro, NC
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Bakersfield, CA
- Parts Used:
- WP2313637
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I ha
... Read more
d ice cubes within a couple of hours
Read less
Was this instruction helpful to you?
Thank you for voting!