Models
>
EC5150WV2
EC5150WV2 Whirlpool Ice Maker
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for EC5150WV2
Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
$7.60
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Aug 13
$7.60
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
Order now and your part arrives by Aug 13
$27.83
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may...
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
$164.55
This kit is intended for use with refrigerators that have a water dispenser in the door.
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
$11.98
This is a compression nut for your refrigerator/freezer. The compression nut is used with the plastic water line for the icemaker assembly. It is the connection between the water supply line and the o...
On Order
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
This single outlet water valve is intended for use with some commercial ice machines, and not refrigerator icemakers. It comes with a mounting bracket, two screws, and a washer.
No Longer Available
In Stock
Order now and your part arrives by Aug 13
$322.52
This part helps circulate water through the evaporator to form ice that will be cut into cubes.
Special Order
Common Problems and Symptoms for EC5150WV2
Viewing 4 of 4Leaking
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Tuckerton, NJ
- Parts Used:
- WP4388152
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Nozzle was broken
Didn't know if part was replaced from the front or back of door. Removed back/inside first. Good excuse to clean mold found in places not normally seen. The only real problem was getting the face off the dispenser without breaking it. I now know it snaps off from the bottom. To replace one little nozzle you have to replace about 10'
... Read more
of tube. When I pulled the old tube out. I attached fishing line to it and used to fishing line to help feed the new tube through the door.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Danville, AL
- Parts Used:
- WP4388152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Water leaked on floor when water dispenser was used.
1. Turn off water supply to refrigerator.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors. ... Read more
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors. ... Read more
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLAS from MCALLEN, TX
- Parts Used:
- WP756782
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
The water pump broke (too old).
I removed the three nuts that hold the old pump, easy. Next step was to replace with the new pump, tricky, because it goes real deep in the machine and my arms barely reach it.
After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake.
What I liked most, is that you don't need to do any ... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump.
What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!!
Last night I fixed it, and today I'm enjoying again fresh ice.
One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice!
Thanks a lot PartSelect !!!
After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake.
What I liked most, is that you don't need to do any ... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump.
What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!!
Last night I fixed it, and today I'm enjoying again fresh ice.
One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice!
Thanks a lot PartSelect !!!
Read less
Was this instruction helpful to you?
Thank you for voting!