Models
>
WUI95X15HZ02
WUI95X15HZ02 Whirlpool Ice Maker
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WUI95X15HZ02
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$79.61
Want cleaner, better-tasting water from your fridge or ice maker? This water filter does the trick by removing unwanted particles and keeping your water fresh. It’s a genuine replacement part and supe...
In Stock
Order now and your part arrives by Mar 27
$28.91
This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light ...
In Stock
Order now and your part arrives by Mar 27
In Stock
Order now and your part arrives by Mar 27
This temperature sensor monitors the ice bin in select refrigerators to help regulate ice production. It sends temperature readings to the control board, preventing overfilling or melting. Compatible ...
In Stock
Order now and your part arrives by Mar 27
In Stock
Order now and your part arrives by Mar 27
In Stock
Order now and your part arrives by Mar 27
In Stock
Order now and your part arrives by Mar 27
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
In Stock
Order now and your part arrives by Mar 27
$70.05
This fan motor is most times used with frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, cooling the compress...
In Stock
Order now and your part arrives by Mar 27
The water distributor tube distributes water from the reservoir to the evaporator plate.
In Stock
Order now and your part arrives by Mar 27
In Stock
Order now and your part arrives by Mar 27
$157.15
The circulation pump is an essential component of select ice makers. It continuously circulates water over the evaporator plate, allowing ice to form into a solid slab before being cut into cubes. Thi...
In Stock
Order now and your part arrives by Mar 27
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WUI95X15HZ02
Viewing 6 of 6Light not working
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Oceanport, NJ
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door switch module wore out
Pull out old module...
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from WILLIAMSBURG, VA
- Parts Used:
- W11542868
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water not refilling after initial batch of ice
The water filled on startup (actually over-filled, which was a clue). After that water was used to make ice, no new water came in so the recirculation pump just made whining noises in the mostly empty reservoir. Since water could come in (on start up) I reasoned it wasn't the water inlet valve, and everything else suggested the ice maker
... Read more
was getting inaccurate info about how much water was in the reservoir. Turns out, the water recirculation pump has a water level sensor built in. So while the pump itself still functioned, the water level sensor inside had gone bad. Replacing the pump fixed the issue. There are videos online that show how to accomplish that, but it was pretty straight-forward. The dis-assembly was sometimes irritating because it's hard to see and maneuver around inside. It'll help if you put the machine closer to eye level. Pay close attention to videos that show the disassembly because there are a couple of tabs that are hard to find.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from N CHESTERFLD, VA
- Parts Used:
- WPW10511923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice bin overfilling
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti
... Read more
c panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
Read less
Was this instruction helpful to you?
Thank you for voting!