Models > MIM1554XRS0

MIM1554XRS0 Maytag Ice Maker

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for MIM1554XRS0

Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
This condenser fan motor kit is used in icemakers and freezers, the purpose is to circulate air through the condenser in the compressor area in order to keep it cool. If your fridge is making loud noi...
In Stock
$67.97
Used with stand-alone ice cube makers.
In Stock
$75.76
This part monitors the temperature and sends the readings to the electronic control board.
In Stock
There is approximately 10'of wire. Note:2 kits are needed to replace both directions.
In Stock
This part controls the light.
In Stock
This is an ice cutter grid assembly for your ice maker. If your machine is not producing ice properly, the assembly may need replacing. You will find this part in the main unit of the ice maker. The t...
In Stock
This part is located in the water pump area of the ice cube maker.
On Order
$11.12
Sold individually.
In Stock
In Stock
This part is a drain pump for your ice maker. When you flush the reservoir on your ice maker to remove impurities, the drain pump is the part that removes the water from the reservoir. This is an auth...
In Stock
$7.97
Sold individually.
In Stock
$11.83
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for MIM1554XRS0

Viewing 9 of 9
Noisy
Fixed by these parts
Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
Fixing
How to fix it
Clicking sound
Fixed by these parts
Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Josue from Jacksonville, NC
Parts Used:
W10124096
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Seven year old condenser fan was making noise when it was running.
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.
199 of 210 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from Hays, KS
Parts Used:
WP2149705
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Broken light switch
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
77 of 128 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Jefferson City, MO
Parts Used:
W10124096
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Fridge made noise and the center post was HOT!
We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must o rder a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.

Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.

Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!
53 of 59 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!