Models > KUIO18NNZS0

KUIO18NNZS0 KitchenAid Ice Maker

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for KUIO18NNZS0

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste...
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
$13.09
This screw is sold individually.
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light ...
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
This bin temperature sensor is for ice makers. The bin temperature sensor monitors the temperature in the ice maker bin and sends the temperature reading to the electronic control board. Disconn...
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
$11.10
Sold individually.
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
Used with freestanding ice cube makers.
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
In Stock
Order within the next 1 hr and 29 mins and your part ships today!
The water distributor tube distributes water from the reservoir to the evaporator plate.
In Stock
Order within the next 1 hr and 29 mins and your part ships today!

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for KUIO18NNZS0

Viewing 3 of 3
Light not working
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Ice maker not making ice
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michelle from Richardson, TX
Parts Used:
72017
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
64 of 125 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Oceanport, NJ
Parts Used:
W11291138
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Door switch module wore out
Pull out old module...
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..

Order new switch..

Fed Ex pkg came on 2nd day..

Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done
40 of 55 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Travis from N CHESTERFLD, VA
Parts Used:
WPW10511923
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Ice bin overfilling
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti c panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!